> Can you set wdcdebug_atapi_mask and wdcdebug_mask to 0x10 (DEBUG_PROBE) and
> send me the boot messages ?
Thanks for the quick reply.

	-- Lennart

NetBSD 1.4Y (SB-FW) #1: Tue May  9 20:27:30 PDT 2000
    augustss@sandburst.lcs.mit.edu:/usr/src/sys/arch/i386/compile/SB-FW
cpu0: family 6 model 8 step 3
cpu0: Intel Pentium III (E) (686-class)
total memory = 64064 KB
avail memory = 56536 KB
using 826 buffers containing 3304 KB of memory
BIOS32 rev. 0 found at 0xfd8a0
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82810 Memory Controller Hub (rev. 0x03)
vga0 at pci0 dev 1 function 0: Intel 82810 Graphics Controller (rev. 0x03)
wsdisplay0 at vga0: console (80x25, vt100 emulation)
ppb0 at pci0 dev 30 function 0: Intel 82801AA Hub-to-PCI Bridge (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
rtk0 at pci1 dev 11 function 0: RealTek 8139 10/100BaseTX
rtk0: interrupting at irq 5
rtk0: Ethernet address 00:50:ba:d8:1d:ca
ukphy0 at rtk0 phy 7: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000000, model 0x0000, rev. 0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
tlp0 at pci1 dev 13 function 0: Lite-On 82C169 Ethernet, pass 2.0
tlp0: interrupting at irq 9
tlp0: Ethernet address 00:a0:cc:62:85:82
ukphy1 at tlp0 phy 1: Generic IEEE 802.3u media interface
ukphy1: BCM5201 10/100 media interface (OUI 0x001018, model 0x0021), rev. 2
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
Conexant Systems product 0x2013 (miscellaneous communications, revision 0x01) at pci1 dev 14 function 0 not configured
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801AA LPC Interface Bridge (rev. 0x02)
pciide0 at pci0 dev 31 function 1: Intel 82801AA IDE Controller (ICH)
pciide0: bus-master DMA support present
pciide0: primary channel wired to compatibility mode
pciide0:0: before reset, st0=0x50, st1=0x0
pciide0:0:0: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
pciide0:0:1: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
pciide0:0: wdcwait_reset() end, st0=0x50, st1=0x0
pciide0:0: after reset, ret_value=0x3
pciide0:0:0: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
pciide0:0:1: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
wdcwait: timeout (time=10001), status 0 error 0 (mask 0x48 bits 0x40)
wdc_ata_get_parms: wdc_c.flags=0xb1
wdcwait: timeout (time=10001), status 0 error 0 (mask 0x48 bits 0x40)
wdc_ata_get_parms: wdc_c.flags=0xb1
pciide0:0:1: IDENTIFY failed (1)
wdcattach: ch_drive_flags 0x1 0x0
wd0 at pciide0 channel 0 drive 0: <SAMSUNG SV1533D>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 14598 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 29897280 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4
pciide0:0:0: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
pciide0:0:1: after reset, sc=0x1 sn=0x1 cl=0x0 ch=0x0
pciide0:0: wdcwait_reset() end, st0=0x50, st1=0x0
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data transfers)
pciide0: secondary channel wired to compatibility mode
pciide0:1: before reset, st0=0x50, st1=0x7f
pciide0:1:0: after reset, sc=0x3 sn=0x1 cl=0x14 ch=0xeb
pciide0:1:1: after reset, sc=0x7f sn=0x7f cl=0x7f ch=0x7f
pciide0:1: wdcwait_reset() end, st0=0x0, st1=0x7f
pciide0:1: after reset, ret_value=0x3
pciide0:1:0: after reset, sc=0x3 sn=0x1 cl=0x14 ch=0xeb
pciide0:1:1: after reset, sc=0x7f sn=0x7f cl=0x7f ch=0x7f
wdcwait: timeout (time=10001), status 0 error 1 (mask 0x48 bits 0x40)
wdc_ata_get_parms: wdc_c.flags=0xb1
wdcwait: timeout (time=10001), status 0 error 1 (mask 0x48 bits 0x40)
wdc_ata_get_parms: wdc_c.flags=0xb1
pciide0:1:0: IDENTIFY failed (1)
wdcwait: timeout (time=10001), status 7f error 7f (mask 0x48 bits 0x40)
wdc_ata_get_parms: wdc_c.flags=0x1f1
wdcwait: timeout (time=10001), status 7f error 7f (mask 0x48 bits 0x40)
wdc_ata_get_parms: wdc_c.flags=0x1f1
pciide0:1:1: IDENTIFY failed (1)
wdcattach: ch_drive_flags 0x0 0x0
pciide0: disabling secondary channel (no drives)
uhci0 at pci0 dev 31 function 2: Intel 82801AA USB Controller (rev. 0x02)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
Intel 82801AA SMBus Controller (SMBus serial bus, revision 0x02) at pci0 dev 31 function 3 not configured
Intel 82801AA AC-97 Audio Controller (audio multimedia, revision 0x02) at pci0 dev 31 function 5 not configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
lpt0 at isa0 port 0x378-0x37b irq 7
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
npx0 at isa0 port 0xf0-0xff: using exception 16
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
apm0 at mainbus0: Power Management spec V1.2
biomask ed4d netmask ef6d ttymask ffef
IPsec: Initialized Security Association Processing.
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
IP Filter: v3.4.1 initialized.  Default = pass all, Logging = enabled
vga: pcvt font support not built in, see vga(4)
vga: pcvt font support not built in, see vga(4)
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25bf, vt100 emulation)
vga_init_screen: no font
wsdisplay0: screen 3 added (80x50, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0