Subject: Re: Fw: Raid10
To: None <port-i386@netbsd.org>
From: dkwok <dkwok@iware.com.au>
List: port-i386
Date: 06/27/2001 21:49:23
Thank you, Guys

You are sport on. But it say 4 partitions in the first place?

Also why the raid partition has to start from e not a if a is available?

DavidKwok
----- Original Message -----
From: Greg Oster <oster@cs.usask.ca>
To: dkwok <dkwok@iware.com.au>
Cc: <port-i386@netbsd.org>
Sent: Wednesday, June 27, 2001 4:42 PM
Subject: Re: Fw: Raid10


> "dkwok" writes:
> >
> > ----- Original Message -----
> > From: dkwok <dkwok@iware.com.au>
> > To: <port-i386@netbsd.org>
> > Sent: Tuesday, June 26, 2001 2:19 PM
> > Subject: Raid10
> >
> >
> > > I am running NetBSD-1.5.1_BETA2.
> > >
> > > I am building a Raid10 set which consists of 4 ide disks, wd0, wd1,
wd2 &
> > > wd3. Wd0 & Wd2 are in a pair and wd 1 & wd3 are in a pairs.
> > >
> > > First I build raid1 set as follows:
> > > wd0 & wd2
> > > a:     500M         0   4.2BSD  1024 8192 16
> > > c:  30000M        0   unused
> > > d:  30000M        0   unused
> > > e:       500M 500M  RAID      # swap disk   - raid0
> > > f:    20000M 1000M RAID     # /  - raid1
> > > g:   27000M  30000M RAID   # strip - raid2
> > >
> > > wd1 & wd3
> > >
> > > c: 15000M   0   unused
> > > d: 15000M   0   unused
> > > e:  15000M   0  RAID              # strip -raid3
> > >
> > > The configuration of raid1 for raid0, raid1, raid2, raid3 is ok. Then
I am
> > > stuck as to how to configure the disklabel of raid2 & raid3 for
stripping.
> > > I have man page, it is very brief on the makeup of raid.conf for raid
on
> > > raid. However my problem is that I cannot setup the disklabel of raid2
and
> > > raid3 by assigning e partition for raid as this:
> > >
> > > raid2
> > > d:  27000M   0   unused
> > > e:  27000M   0    RAID
> > > raid3
> > > d:  15000M   0   unused
> > > e:  15000M   0    RAID
> > > When I replace the disklabel by doing disklabel -R -r raid2
> > > /root/disklabel.raid2, I got the error message saying:
> > >
> > > disklabel: warning: unused partition e: size 27000M offset 0
>
> You don't show the full disklabel, but how many partitions are in the
>
>   8 partitions:
>
> line?  (I'm betting it just says 4...  Bump that to 5 (or 8 or whatever)
> and you should be fine...
>
> > > Anyone has experienced setting up raid10 set?
>
> Yup.
>
> Later...
>
> Greg Oster
>
>
>