Subject: -current no longer boots on asus p4t533-c board
To: None <port-i386@netbsd.org>
From: Markus W Kilbinger <kilbi@rad.rwth-aachen.de>
List: port-i386
Date: 06/12/2003 09:56:55
Hi!

Recent -current changes prevents booting on asus p4t533-c board.
Attached is dmesg's output from my last running kernel (Jun 5th) where
I marked ('**->') the message position where the actual kernels hang
(see below). Other boards (old asus boards) run fine with actual
-current kernels.

-> send-pr? Anything I can test?

Markus.

dmesg output:

  NetBSD 1.6T (RADIX) #0: Thu Jun  5 12:42:43 MEST 2003
  	root@lwle5:/usr/src/sys/arch/i386/compile/RADIX
  total memory = 1023 MB
  avail memory = 946 MB
  using 6144 buffers containing 52504 KB of memory
  BIOS32 rev. 0 found at 0xf1640
  PCI BIOS rev. 2.1 found at 0xf1670
  PCI IRQ Routing Table rev. 1.0 found at 0xf1be0, size 176 bytes (9 entries)
  PCI Interrupt Router at 000:31:0 (Intel 82371FB PCI-to-ISA Bridge (PIIX))
  mainbus0 (root)
  cpu0 at mainbus0: apid 0 (boot processor)
  cpu0: Intel Pentium 4 (686-class), 2405.54 MHz, id 0xf27
  cpu0: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
  cpu0: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
  cpu0: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
  cpu0: I-cache 12K uOp cache 8-way, D-cache 8 KB 64b/line 4-way
  cpu0: L2 cache 512 KB 64b/line 8-way
  cpu0: ITLB 4K/4M: 128 entries
  cpu0: DTLB 4K/4M: 64 entries
  cpu0: calibrating local timer
  cpu0: apic clock running at 133 MHz
  cpu0: 16 page colors
  ioapic0 at mainbus0 apid 4 (I/O APIC)
  ioapic0: pa 0xfec00000, version 20, 24 pins
  acpi0 at mainbus0
  acpi0: X/RSDT: OemId <ASUS  ,P4T533-C,42302e31>, AslId <MSFT,31313031>
  acpi0: SCI interrupting at int 9
  acpi0: fixed-feature power button present
  ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
  ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
  acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
  PNP0C01 at acpi0 not configured
  PNP0C0F at acpi0 not configured
  PNP0C0F at acpi0 not configured
  PNP0C0F at acpi0 not configured
  PNP0C0F at acpi0 not configured
  PNP0C0F at acpi0 not configured
  PNP0A03 at acpi0 not configured
  PNP0C02 at acpi0 not configured
  PNP0C02 at acpi0 not configured
  PNP0000 at acpi0 not configured
  PNP0200 at acpi0 not configured
  PNP0100 at acpi0 not configured
  PNP0B00 at acpi0 not configured
  PNP0800 at acpi0 not configured
  PNP0C04 at acpi0 not configured
  PNP0700 at acpi0 not configured
  PNP0401 at acpi0 not configured
  PNP0501 at acpi0 not configured
  PNP0501 at acpi0 not configured
  PNP0303 at acpi0 not configured
  PNP0C02 at acpi0 not configured
  pci0 at mainbus0 bus 0: configuration mode 1
  pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
  pchb0 at pci0 dev 0 function 0
  pchb0: Intel 82850 Host (rev. 0x04)
  agp0 at pchb0: aperture at 0xf8000000, size 0x4000000
  ppb0 at pci0 dev 1 function 0: Intel 82850/82860 AGP (rev. 0x04)
  pci1 at ppb0 bus 1
  pci1: i/o space, memory space enabled
  vga0 at pci1 dev 0 function 0: Nvidia Corporation GeForce2 MX 100/200 (rev. 0xb2)
  wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation)
  wsmux1: connecting to wsdisplay0
**->
  ppb1 at pci0 dev 30 function 0: Intel 82801BA Hub-to-PCI Bridge (rev. 0x04)
  pci2 at ppb1 bus 2
  pci2: i/o space, memory space enabled
  NEC USB Host Controller (USB serial bus, interface 0x10, revision 0x41) at pci2 dev 4 function 0 not configured
  NEC USB Host Controller (USB serial bus, interface 0x10, revision 0x41) at pci2 dev 4 function 1 not configured
  NEC USB Host Controller (USB serial bus, interface 0x20, revision 0x02) at pci2 dev 4 function 2 not configured
  wm0 at pci2 dev 10 function 0: Intel i82545EM 1000BASE-T Ethernet, rev. 1
  wm0: interrupting at apic 4 int 22 (irq 5)
  wm0: Ethernet address 00:07:e9:xx:xx:xx
  makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
  makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
  wm1 at pci2 dev 11 function 0: Intel i82545EM 1000BASE-T Ethernet, rev. 1
  wm1: interrupting at apic 4 int 23 (irq 9)
  wm1: Ethernet address 00:07:e9:xx:x:xx
  makphy1 at wm1 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
  makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
  pcib0 at pci0 dev 31 function 0
  pcib0: Intel 82801BA LPC Interface Bridge (rev. 0x04)
  pciide0 at pci0 dev 31 function 1: Intel 82801BA IDE Controller (ICH2) (rev. 0x04)
  pciide0: bus-master DMA support present
  pciide0: primary channel wired to compatibility mode
  wd0 at pciide0 channel 0 drive 0: <ST380023A>
  wd0: drive supports 16-sector PIO transfers, LBA addressing
  wd0: 76319 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
  wd0: 32-bit data port
  wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
  wd1 at pciide0 channel 0 drive 1: <ST380023A>
  wd1: drive supports 16-sector PIO transfers, LBA addressing
  wd1: 76319 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 156301488 sectors
  wd1: 32-bit data port
  wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
  pciide0: primary channel interrupting at irq 14
  wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
  wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
  pciide0: secondary channel wired to compatibility mode
  atapibus0 at pciide0 channel 1: 2 targets
  cd0 at atapibus0 drive 0: <HL-DT-ST CD-ROM GCR-8520B, , 1.00> cdrom removable
  cd0: 32-bit data port
  cd0M-}?supports PIO mode 4, DMA mode 2
  pciide0: secondary channel interrupting at irq 15
  cd0(pciide0:1:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
  Intel 82801BA USB Controller (USB serial bus, revision 0x04) at pci0 dev 31 function 2 not configured
  Intel 82801BA USB Controller (USB serial bus, revision 0x04) at pci0 dev 31 function 4 not configured
  isa0 at pcib0
  com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
  com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
  pckbc0 at isa0 port 0x60-0x64
  pckbd0 at pckbc0 (kbd slot)
  pckbc0: using irq 1 for kbd slot
  wskbd0 at pckbd0: console keyboard, using wsdisplay0
  lpt0 at isa0 port 0x378-0x37b irq 7
  pcppi0 at isa0 port 0x61
  spkr0 at pcppi0
  sysbeep0 at pcppi0
  npx0 at isa0 port 0xf0-0xff: using exception 16
  fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
  ioapic0: enabling
  Kernelized RAIDframe activated
  IPsec: Initialized Security Association Processing.
  raid0: RAID Level 1
  raid0: Components: /dev/wd0b /dev/wd1b
  raid0: Total Sectors: 78129920 (38149 MB)
  raid1: RAID Level 0
  raid1: Components: /dev/wd0e /dev/wd1e
  raid1: Total Sectors: 156141056 (76240 MB)
  boot device: raid0
  root on raid0a dumps on raid0b
  root file system type: ffs
  IP Filter: v3.4.29 initialized.  Default = pass all, Logging = enabled
  wsdisplay0: screen 1 added (80x25, vt100 emulation)
  wsdisplay0: screen 2 added (80x25, vt100 emulation)
  wsdisplay0: screen 3 added (80x25, vt100 emulation)
  wsdisplay0: screen 4 added (80x25, vt100 emulation)