> 	If you have a working base system, you can modify  
> INSTALL_LAPTOP and GENERIC_LAPTOP and build.sh relase, then make an  
> bootable ISO out of $RELDIR
> It took me about 10 tries to get a working INSTALL_LAPTOP for my Sony  
> Vaio (ACPI dependant).
> options         ACPI_PCI_FIXUP          # PCI interrupt routing via  
> ACPI
> options         ACPI_ACTIVATE_DEV       # If set, activate inactive  
> devices
> # Configure PCI using BIOS information
> options         PCIBIOS                 # PCI BIOS support
> #options        PCIBIOSVERBOSE          # PCI BIOS verbose info
> options         PCIBIOS_ADDR_FIXUP      # fixup PCI I/O addresses
> options         PCIBIOS_BUS_FIXUP       # fixup PCI bus numbering
> options         PCIBIOS_INTR_FIXUP      # fixup PCI interrupt routing
> #options        PCIBIOS_IRQS_HINT=0x0a00 # PCI interrupts hint. IRQ 9  
> or 11
> options         PCIBIOS_INTR_GUESS      # see pcibios(4)
> #options        PCIINTR_DEBUG           # super-verbose PCI interrupt  
> fixup

Thanks Brian for your advice.  I did the above and enabled ACPI,
and it would still crash.  However, when I disabled pcmcia+pcic
& cardbus+cbb the modified general kernel would boot with ACPI
enabled.

I have just taken the newest "ACPI-CA 20031203" changes uploaded
to current last night by Takayoshi Kochi <kochi@NetBSD.org>, and
rebuilt a new kernel with ACPI enabled.  Unfortunately, when I
enable cardbus & pcmcia in the kernel, I still get the exact same
following error:

============================================================================
ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-to-PCI Bridge (rev. 0x83)
pci1 at ppb0 bus 1
pci1: i/o space memory enabled
cbb0 at pci1 dev 3 function 0: Ricoh 5C475 PCI-CardBus bridge (rev. 0xb8)
uvm_fault(0xc060a0c0, 0, 0, 1) -> 0xe
kernel: page fault trap, code=0
Stopped in pid 0.1 (swapper) at netbsd:rbus_new_root_share+0xc: cmpl
	0xc(%ecx),%edx
============================================================================

Brian, what type of Sony Vaio laptop do you have?  Does it have
Intel Centrino?

Has anyone been able to get any Centrino laptop to work properly
under NetBSD?  Does NetBSD have any support for the Centrino built
in Wi/Fi and ACPI implementations associated with it?

I have attached a copy of my kernel boot messages with the newest
ACPI changes uploaded by Takayoshi, but with the cardbus + pcmcia
disabled in order to get my JVC-Victor Interlink MP-XP7310 laptop
to boot successfully.  Looking at these boot messages, it would
appear that a lot of ACPI stuff is still not working properly in
NetBSD with my laptop, but I could be wrong.

Takayoshi as the expert, could you please look over the kernel
boot messages below, and comment on whether or not it is okay?

Any additional assistance would be greatly appreciated.  I need
to get the CardBus+PCMCIA slot, Wi/Fi, and Power Manager to all
work properly.

Thanks in advance.
Alicia.

============================================================================
NetBSD 1.6ZG (GEN) #0: Sun Dec 14 17:31:04 EST 2003
	root@luna.engine.ca:/usr/src/sys/arch/i386/compile/GEN
total memory = 502 MB
avail memory = 459 MB
using 6144 buffers containing 25848 KB of memory
mainbus0 (root)
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel Pentium M (Banias) (686-class), 1000.09 MHz, id 0x695
cpu0: features a7e9fbbf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,APIC,SEP,MTRR>
cpu0: features a7e9fbbf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features a7e9fbbf<FXSR,SSE,SSE2,TM,SBF>
cpu0: calibrating local timer
cpu0: apic clock running at 100 MHz
ioapic0 at mainbus0 apid 1 (I/O APIC)
ioapic0: pa 0xfec00000, version 20, 24 pins
ioapic0: misconfigured as apic 0
ioapic0: remapped to apic 1
acpi0 at mainbus0
acpi0: using Intel ACPI CA subsystem version 20031029
acpi0: X/RSDT: OemId <A M I ,OEMRSDT ,08000307>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
acpi: activated PNP0C0F
acpi: activated PNP0C0F
acpi: activated PNP0C0F
PNP0A03 [PCI Bus] at acpi0 not configured
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
PNP0100 [AT Timer] at acpi0 not configured
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pckbc1 at acpi0 (PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (PNP0F03): aux port
pckbc2: irq 12
PNP0800 [AT-style speaker sound] at acpi0 not configured
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: using exception 16
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
acpiec0 at acpi0 (PNP0C09): ACPI Embedded Controller
acpiec0: io 0x62,0x66
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configured
acpiacad0 at acpi0 (ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (PNP0C0A-0): ACPI Battery (Control Method)
acpibat1 at acpi0 (PNP0C0A-1): ACPI Battery (Control Method)
PNP0C01 [System Board] at acpi0 not configured
acpibut0 at acpi0 (PNP0C0C): ACPI Power Button
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
ATK0100 at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
PNP0C0F [PCI interrupt link device] at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel 82855GM Host-to-Hub Controller (rev. 0x02)
agp0 at pchb0: detected 8060k stolen memory
agp0: aperture size is 128M
agp0: aperture at 0xf0000000, size 0x8000000
Intel 82855GM GMCH Memory Controller (miscellaneous system, revision 0x02) at pci0 dev 0 function 1 not configured
Intel 82855GM GMCH Configuration Process (miscellaneous system, revision 0x02) at pci0 dev 0 function 3 not configured
vga1 at pci0 dev 2 function 0: Intel 82855GM GMCH Integrated Graphics Device (rev. 0x02)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
Intel 82855GM GMCH Integrated Graphics Device (miscellaneous display, revision 0x02) at pci0 dev 2 function 1 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801DB/DBM USB UHCI Controller #1 (rev. 0x03)
uhci0: interrupting at ioapic0 pin 16 (irq 5)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801DB/DBM USB UHCI Controller #2 (rev. 0x03)
uhci1: interrupting at ioapic0 pin 19 (irq 4)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: Intel 82801DB/DBM USB UHCI Controller #3 (rev. 0x03)
uhci2: interrupting at ioapic0 pin 18 (irq 7)
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801DB/DBM USB EHCI Controller (rev. 0x03)
ehci0: interrupting at ioapic0 pin 23 (irq 3)
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb0 at pci0 dev 30 function 0: Intel 82801BAM Hub-to-PCI Bridge (rev. 0x83)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
Ricoh 5C475 PCI-CardBus bridge (CardBus bridge, revision 0xb8) at pci1 dev 3 function 0 not configured
Ricoh 5C551 PCI-CardBus bridge/Firewire (Firewire serial bus, interface 0x10) at pci1 dev 3 function 1 not configured
Intel PRO/Wireless LAN 2100 3B Mini PCI Adapter (miscellaneous network, revision 0x04) at pci1 dev 5 function 0 not configured
fxp0 at pci1 dev 8 function 0: Intel PRO/100 VM (MOB) Network Controller, rev 131
fxp0: interrupting at ioapic0 pin 20 (irq 5)
fxp0: Ethernet address 00:80:88:03:51:55
inphy0 at fxp0 phy 1: i82562EM 10/100 media interface, rev. 0
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801DB ISA Bridge (rev. 0x03)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x03)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at piixide0 channel 1
auich0 at pci0 dev 31 function 5: i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: can't map codec i/o space
Intel 82801DB/DBM AC97 Modem Controller (modem communications, revision 0x03) at pci0 dev 31 function 6 not configured
isa0 at pcib0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
ioapic0: enabling
wd0 at atabus0 drive 0: <IC25N040ATMR04-0>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 38154 MB, 77520 cyl, 16 head, 63 sec, 512 bytes/sect x 78140160 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA data transfers)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
============================================================================