--pgp-sign-Multipart_Thu_Sep__6_15:24:33_2007-1
Content-Type: text/plain; charset=US-ASCII
Content-Transfer-Encoding: quoted-printable

At Tue, 23 May 2006 20:14:55 -0400, Me-weird.com wrote:
Subject: Re: pckbc(4) not working with 3.0 GENERIC.MPACPI kernel....
>=20

Still no-go on the keyboard for this fancy IBM xSeries 336 server even
with 4.0_RC1.

There is a keyboard attached during boot, and it does work fine in the
BIOS, and when booting a non-ACPI kernel.

Note the error "pckbc: initial cmd word write error"

The same kernel attaches pckbc0 just fine on my Dell PE2650.

Perhaps unrelated, but any ACPI kernel still fails miserably on my Asus
P2B-D machine too.  The keyboard doesn't work and interrupts for the
piixide(4) driver seem to be lost....  FreeBSD-6.2 works fine on this
machine with its ACPI support so there must be a secret to be found
there somewhere.

I'm going to try FreeBSD-6.2 on the IBM just for kicks too.

Here's all the output with ACPIVERBOSE and ACPI_DEBUG from the IBM:

# dmesg
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2=
006
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.0_RC1 (GENERIC.MP) #1: Thu Sep  6 12:35:02 EDT 2007
        woods@once:/build/woods/once/netbsd-4-i386-i386-ppro-obj/building/w=
ork/woods/m-NetBSD-4/sys/arch/i386/compile/GENERIC.MP
total memory =3D 3327 MB
rbus: rbus_min_start set to 0xc0000000
avail memory =3D 3257 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
BIOS32 rev. 0 found at 0xfd6f1
SMBIOS rev. 2.3 @ 0xf5eea (52 entries)
PCI BIOS rev. 2.1 found at 0xfd72e
pcibios: config mechanism [1][x], special cycles [1][x], last bus 8
PCI BIOS has 11 Interrupt Routing table entries
PCI Exclusive IRQs: 9 10 11 15
mainbus0 (root)
mainbus0: scanning 0x9d400 to 0x9d7f0 for MP signature
mainbus0: MP floating pointer found in extended bios data area at 0x9d540
mainbus0: MP config table at 0x9e520, 388 bytes long
 tbxface-0196 [01] LoadTables            : ACPI Tables successfully acquired
Parsing all Control Methods:
Table [DSDT](id 0005) - 262 Objects with 37 Devices 71 Methods 9 Regions
ACPI Namespace successfully loaded at root 0xc0a576a4
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel (686-class), 3000.38 MHz, id 0xf43
cpu0: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu0: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 641d<SSE3,MONITOR,DS-CPL,CID,xTPR>
cpu0: features3 20100000<XD,EM64T>
cpu0: "Intel(R) Xeon(TM) CPU 3.00GHz"
cpu0: I-cache 12K uOp cache 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: ITLB 4K/4M: 64 entries
cpu0: DTLB 4K/4M: 64 entries
cpu0: using thermal monitor 1
cpu0: calibrating local timer
cpu0: apic clock running at 200 MHz
cpu0: 64 page colors
cpu0: kstack at 0xce2a5000 for 12288 bytes
cpu0: idle pcb at 0xce2a5000, idle sp at 0xce2a7f98
cpu1 at mainbus0: apid 6 (application processor)
cpu1: starting
cpu1: Intel (686-class), 3000.12 MHz, id 0xf43
cpu1: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu1: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu1: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu1: features2 641d<SSE3,MONITOR,DS-CPL,CID,xTPR>
cpu1: features3 20100000<XD,EM64T>
cpu1: "Intel(R) Xeon(TM) CPU 3.00GHz"
cpu1: I-cache 12K uOp cache 8-way
cpu1: L2 cache 2 MB 64B/line 8-way
cpu1: ITLB 4K/4M: 64 entries
cpu1: DTLB 4K/4M: 64 entries
cpu1: using thermal monitor 1
cpu1: kstack at 0xce2ae000 for 12288 bytes
cpu1: idle pcb at 0xce2ae000, idle sp at 0xce2b0f98
cpu2 at mainbus0: apid 1 (application processor)
cpu2: starting
cpu2: Intel (686-class), 3000.11 MHz, id 0xf43
cpu2: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu2: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu2: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu2: features2 641d<SSE3,MONITOR,DS-CPL,CID,xTPR>
cpu2: features3 20100000<XD,EM64T>
cpu2: "Intel(R) Xeon(TM) CPU 3.00GHz"
cpu2: I-cache 12K uOp cache 8-way
cpu2: L2 cache 2 MB 64B/line 8-way
cpu2: ITLB 4K/4M: 64 entries
cpu2: DTLB 4K/4M: 64 entries
cpu2: using thermal monitor 1
cpu2: kstack at 0xce2c7000 for 12288 bytes
cpu2: idle pcb at 0xce2c7000, idle sp at 0xce2c9f98
cpu3 at mainbus0: apid 7 (application processor)
cpu3: starting
cpu3: Intel (686-class), 3000.11 MHz, id 0xf43
cpu3: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu3: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu3: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu3: features2 641d<SSE3,MONITOR,DS-CPL,CID,xTPR>
cpu3: features3 20100000<XD,EM64T>
cpu3: "Intel(R) Xeon(TM) CPU 3.00GHz"
cpu3: I-cache 12K uOp cache 8-way
cpu3: L2 cache 2 MB 64B/line 8-way
cpu3: ITLB 4K/4M: 64 entries
cpu3: DTLB 4K/4M: 64 entries
cpu3: using thermal monitor 1
cpu3: kstack at 0xce2e0000 for 12288 bytes
cpu3: idle pcb at 0xce2e0000, idle sp at 0xce2e2f98
ioapic0 at mainbus0 apid 14 (I/O APIC)
ioapic0: pa 0xfec00000, virtual wire mode, version 20, 24 pins
ioapic1 at mainbus0 apid 13 (I/O APIC)
ioapic1: pa 0xfec82000, virtual wire mode, version 20, 24 pins
ioapic2 at mainbus0 apid 12 (I/O APIC)
ioapic2: pa 0xfec82400, virtual wire mode, version 20, 24 pins
acpi0 at mainbus0: Advanced Configuration and Power Interface
acpi0: using Intel ACPI CA subsystem version 20060217
acpi0: X/RSDT: OemId <IBM   ,SERONYXP,00001001>, AslId <IBM ,45444f43>
evxfevnt-0177 [02] Enable                : Transition to ACPI mode successf=
ul
evgpeblk-1111 [08] EvCreateGpeBlock      : GPE 00 to 1F [_GPE] 4 regs on in=
t 0x9
evgpeblk-1211 [07] EvInitializeGpeBlock  : Found 1 Wake, Enabled 0 Runtime =
GPEs in this block
Completing Region/Field/Buffer/Package initialization:.....................=
...........
Initialized 9/9 Regions 0/0 Fields 10/10 Buffers 13/14 Packages (271 nodes)
Executing all Device _STA and_INI methods:.................................=
..........
43 Devices found - executed 0 _STA, 0 _INI methods
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
mpacpi: found root PCI bus 0 at level 1
mpacpi: found subordinate bus 4 at level 3
mpacpi: found subordinate bus 5 at level 3
mpacpi: found subordinate bus 1 at level 2
mpacpi: 4 PCI busses
mpacpi: ISA interrupt override  0 -> 2
mpacpi: ISA interrupt override  9 -> 9
mpacpi: configuring PCI bus 0 int routing
mpacpi: configuring PCI bus 4 int routing
mpacpi: configuring PCI bus 5 int routing
mpacpi: configuring PCI bus 1 int routing
ioapic0: pin 2 attached to isa0 irq 0 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 1 attached to isa0 irq 1 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 3 attached to isa0 irq 3 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 4 attached to isa0 irq 4 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 5 attached to isa0 irq 5 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 6 attached to isa0 irq 6 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 7 attached to isa0 irq 7 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 8 attached to isa0 irq 8 (type 0<type=3D0> flags 0<pol=3D0,tri=
g=3D0>)
ioapic0: pin 9 attached to isa0 irq 9 (type 0<type=3D0> flags d<pol=3D1=3DA=
ct Hi,trig=3D3=3DLevel>)
ioapic0: pin 10 attached to isa0 irq 10 (type 0<type=3D0> flags 0<pol=3D0,t=
rig=3D0>)
ioapic0: pin 11 attached to isa0 irq 11 (type 0<type=3D0> flags 0<pol=3D0,t=
rig=3D0>)
ioapic0: pin 12 attached to isa0 irq 12 (type 0<type=3D0> flags 0<pol=3D0,t=
rig=3D0>)
ioapic0: pin 13 attached to isa0 irq 13 (type 0<type=3D0> flags 0<pol=3D0,t=
rig=3D0>)
ioapic0: pin 14 attached to isa0 irq 14 (type 0<type=3D0> flags 0<pol=3D0,t=
rig=3D0>)
ioapic0: pin 15 attached to isa0 irq 15 (type 0<type=3D0> flags 0<pol=3D0,t=
rig=3D0>)
local apic: pin 1 attached to NMI (type 1<type=3D1=3DNMI> flags 0<pol=3D0,t=
rig=3D0>)
local apic: pin 1 attached to NMI (type 1<type=3D1=3DNMI> flags 0<pol=3D0,t=
rig=3D0>)
local apic: pin 1 attached to NMI (type 1<type=3D1=3DNMI> flags 0<pol=3D0,t=
rig=3D0>)
local apic: pin 1 attached to NMI (type 1<type=3D1=3DNMI> flags 0<pol=3D0,t=
rig=3D0>)
ioapic0: pin 16 attached to pci0 device 2 INT_A (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 17 attached to pci0 device 2 INT_B (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 18 attached to pci0 device 2 INT_C (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 19 attached to pci0 device 2 INT_D (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 16 attached to pci0 device 4 INT_A (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 17 attached to pci0 device 4 INT_B (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 18 attached to pci0 device 4 INT_C (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 19 attached to pci0 device 4 INT_D (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 16 attached to pci0 device 6 INT_A (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 17 attached to pci0 device 6 INT_B (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 18 attached to pci0 device 6 INT_C (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 19 attached to pci0 device 6 INT_D (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 16 attached to pci0 device 7 INT_A (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 17 attached to pci0 device 7 INT_B (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 18 attached to pci0 device 7 INT_C (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 19 attached to pci0 device 7 INT_D (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 16 attached to pci0 device 29 INT_A (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 19 attached to pci0 device 29 INT_B (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 18 attached to pci0 device 29 INT_C (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 23 attached to pci0 device 29 INT_D (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 16 attached to pci0 device 30 INT_A (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 17 attached to pci0 device 30 INT_B (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 18 attached to pci0 device 30 INT_C (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 19 attached to pci0 device 30 INT_D (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 17 attached to pci0 device 31 INT_B (type 0<type=3D0> flags f<=
pol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic1: pin 4 attached to pci4 device 1 INT_A (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic1: pin 5 attached to pci4 device 1 INT_B (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic1: pin 0 attached to pci4 device 2 INT_A (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic1: pin 1 attached to pci4 device 2 INT_B (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic1: pin 2 attached to pci4 device 2 INT_C (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic1: pin 3 attached to pci4 device 2 INT_D (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic2: pin 0 attached to pci5 device 1 INT_A (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic2: pin 1 attached to pci5 device 1 INT_B (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic2: pin 2 attached to pci5 device 1 INT_C (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic2: pin 3 attached to pci5 device 1 INT_D (type 0<type=3D0> flags f<po=
l=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 16 attached to pci1 device 1 INT_A (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ioapic0: pin 20 attached to pci1 device 8 INT_A (type 0<type=3D0> flags f<p=
ol=3D3=3DAct Lo,trig=3D3=3DLevel>)
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0A08 [PCI Express/PCI-X Mode-2 Host Bridge] at acpi0 not configured
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configu=
red
pckbc0 at acpi0 (PNP0303): kbd port
pckbc0: io 0x64,0x60 irq 1
pckbc1 at acpi0 (PNP0F13): aux port
pckbc1: irq 12
com3 at acpi0 (PNP0501-2)
com3: io 0x3f8-0x3ff irq 4
com3: ns16550a, working fifo
com3: console
PNP0000 [AT Interrupt Controller] at acpi0 not configured
PNP0003 [APIC] at acpi0 not configured
PNP0003 [APIC] at acpi0 not configured
PNP0003 [APIC] at acpi0 not configured
PNP0200 [AT DMA Controller] at acpi0 not configured
attimer1 at acpi0 (PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
PNP0B00 [AT Real-Time Clock] at acpi0 not configured
pcppi1 at acpi0 (PNP0800)
pcppi1: io 0x61
pcppi1: children must have an explicit unit
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
PNP0C02 [Plug and Play motherboard register resources] at acpi0 not configu=
red
apm0 at acpi0: Power Management spec V1.2
apm0: A/C state: unknown
apm0: battery charge state: low
pckbc: initial cmd word write error
pcppi1: attached to attimer1
ipmi0 at mainbus0: version 1.5 interface KCS iobase 0xca8/8 spacing 4
pci0 at mainbus0 bus 0: configuration mode 1mainbus0: added to list as bus 0

pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Intel E7525 Memory Controller Hub (rev. 0x0c)
Intel E7525 Error Reporting Device (undefined subclass 0x00, revision 0x0c)=
 at pci0 dev 0 function 1 not configured
ppb0 at pci0 dev 2 function 0: Intel E7525 PCI Express Port A (rev. 0x0c)
pci1 at ppb0 bus 2ppb0: added to list as bus 2

pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci0 dev 4 function 0: Intel E7525 PCI Express Port B (rev. 0x0c)
pci2 at ppb1 bus 3ppb1: added to list as bus 3

pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci2 dev 0 function 0: Intel 6700PXH PCI Express-to-PCI Bridge #0 (=
rev. 0x09)
pci3 at ppb2 bus 4ppb2: added to list as bus 4

pci3: i/o space, memory space enabled, rd/line, wr/inv ok
mpt0 at pci3 dev 1 function 0: Symbios Logic 53c1030
mpt0: interrupting at ioapic1 pin 4 (irq 11)
scsibus0 at mpt0: 16 targets, 8 luns per target
ppb3 at pci2 dev 0 function 2: Intel 6700PXH PCI Express-to-PCI Bridge #1 (=
rev. 0x09)
pci4 at ppb3 bus 5ppb3: added to list as bus 5

pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci4 dev 1 function 0: IBM 133 PCI-X Bridge (rev. 0x02)
pci5 at ppb4 bus 6ppb4: added to list as bus 6

pci5: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci5 dev 4 function 0: Intel i82546EB 1000BASE-T Ethernet, rev. 1
wm0: interrupting at ioapic2 pin 0 (irq 11)
wm0: 64-bit 120MHz PCIX bus
wm0: 256 word (8 address bits) MicroWire EEPROM
wm0: Ethernet address 00:04:23:b2:91:f0
makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000bas=
eT-FDX, auto
wm1 at pci5 dev 4 function 1: Intel i82546EB 1000BASE-T Ethernet, rev. 1
wm1: interrupting at ioapic2 pin 1 (irq 11)
wm1: 64-bit 120MHz PCIX bus
wm1: 256 word (8 address bits) MicroWire EEPROM
wm1: Ethernet address 00:04:23:b2:91:f1
makphy1 at wm1 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
makphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000bas=
eT-FDX, auto
wm2 at pci5 dev 6 function 0: Intel i82546EB 1000BASE-T Ethernet, rev. 1
wm2: interrupting at ioapic2 pin 2 (irq 3)
wm2: 64-bit 120MHz PCIX bus
wm2: 256 word (8 address bits) MicroWire EEPROM
wm2: Ethernet address 00:04:23:b2:91:f2
makphy2 at wm2 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
makphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000bas=
eT-FDX, auto
wm3 at pci5 dev 6 function 1: Intel i82546EB 1000BASE-T Ethernet, rev. 1
wm3: interrupting at ioapic2 pin 3 (irq 3)
wm3: 64-bit 120MHz PCIX bus
wm3: 256 word (8 address bits) MicroWire EEPROM
wm3: Ethernet address 00:04:23:b2:91:f3
makphy3 at wm3 phy 1: Marvell 88E1011 Gigabit PHY, rev. 3
makphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000bas=
eT-FDX, auto
ppb5 at pci0 dev 6 function 0: Intel product 0x3599 (rev. 0x0c)
pci6 at ppb5 bus 7ppb5: added to list as bus 7

pci6: i/o space, memory space enabled, rd/line, wr/inv ok
bge0 at pci6 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
bge0: interrupting at ioapic0 pin 16 (irq 11)
bge0: pcie mode=3D0x105000
bge0: ASIC BCM5751 A1 (0x4101), Ethernet address 00:14:5e:33:69:ca
bge0: setting short Tx thresholds
brgphy0 at bge0 phy 1: BCM5750 1000BASE-T media interface, rev. 0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000bas=
eT-FDX, auto
ppb6 at pci0 dev 7 function 0: Intel product 0x359a (rev. 0x0c)
pci7 at ppb6 bus 8ppb6: added to list as bus 8

pci7: i/o space, memory space enabled, rd/line, wr/inv ok
bge1 at pci7 dev 0 function 0: Broadcom BCM5721 Gigabit Ethernet
bge1: interrupting at ioapic0 pin 16 (irq 11)
bge1: pcie mode=3D0x105000
bge1: ASIC BCM5751 A1 (0x4101), Ethernet address 00:14:5e:33:69:cb
bge1: setting short Tx thresholds
brgphy1 at bge1 phy 1: BCM5750 1000BASE-T media interface, rev. 0
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000bas=
eT-FDX, auto
Intel product 0x359b (miscellaneous system, revision 0x0c) at pci0 dev 8 fu=
nction 0 not configured
uhci0 at pci0 dev 29 function 0: Intel 82801EB/ER USB UHCI Controller (rev.=
 0x02)
uhci0: interrupting at ioapic0 pin 16 (irq 11)
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel 82801EB/ER USB UHCI Controller (rev.=
 0x02)
uhci1: interrupting at ioapic0 pin 19 (irq 3)
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: Intel 82801EB/ER USB EHCI Controller (rev.=
 0x02)
ehci0: interrupting at ioapic0 pin 23 (irq 3)
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
ppb7 at pci0 dev 30 function 0: Intel 82801BA Hub-PCI Bridge (rev. 0xc2)
pci8 at ppb7 bus 1ppb7: added to list as bus 1

pci8: i/o space, memory space enabled
vga1 at pci8 dev 1 function 0: ATI Technologies Radeon 7000/VE QY (rev. 0x0=
0)
wsdisplay0 at vga1 kbdmux 1
wsmux1: connecting to wsdisplay0
pcib0 at pci0 dev 31 function 0
pcib0: Intel 82801EB LPC Interface Bridge (rev. 0x02)
piixide0 at pci0 dev 31 function 2
piixide0: Intel 82801EB Serial ATA Controller (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14 (irq 14)
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at ioapic0 pin 15 (irq 15)
atabus1 at piixide0 channel 1
Intel 82801EB/ER SMBus Controller (SMBus serial bus, revision 0x02) at pci0=
 dev 31 function 3 not configured
isa0 at pcib0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
cpu0: prelint0 700<vector=3D0,delmode=3D7,dest=3D0> 0<target=3D0>
cpu0: prelint1 400<vector=3D0,delmode=3D4,dest=3D0> 0<target=3D0>
cpu0: timer0 300c0<vector=3Dc0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu0: pcint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu0: lint0 10700<vector=3D0,delmode=3D7,masked,dest=3D0> 0<target=3D0>
cpu0: lint1 400<vector=3D0,delmode=3D4,dest=3D0> 0<target=3D0>
cpu0: err0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
ioapic0: enabling
ioapic0: int4 d0<vector=3Dd0,delmode=3D0,dest=3D0> 0<target=3D0>
ioapic0: int9 80a0<vector=3Da0,delmode=3D0,level,dest=3D0> 0<target=3D0>
ioapic0: int14 64<vector=3D64,delmode=3D0,dest=3D0> 0<target=3D0>
ioapic0: int15 65<vector=3D65,delmode=3D0,dest=3D0> 0<target=3D0>
ioapic0: int16 a061<vector=3D61,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
ioapic0: int19 a062<vector=3D62,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
ioapic0: int23 a063<vector=3D63,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
ioapic1: enabling
ioapic1: int4 a060<vector=3D60,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
ioapic2: enabling
ioapic2: int0 a070<vector=3D70,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
ioapic2: int1 a071<vector=3D71,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
ioapic2: int2 a072<vector=3D72,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
ioapic2: int3 a073<vector=3D73,delmode=3D0,actlo,level,dest=3D0> 0<target=
=3D0>
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <HL-DT-STCD-RW/DVD DRIVE GCC-4246N, , 0Y03> cdrom=
 removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
sd0 at scsibus0 target 0 lun 0: <IBM-ESXS, MAX3073NC     FN, CA06> disk fix=
ed
sd0: 70006 MB, 49158 cyl, 4 head, 729 sec, 512 bytes/sect x 143374000 secto=
rs
sd0: sync (6.25ns offset 127), 16-bit (320.000MB/s) transfers, tagged queue=
ing
sd1 at scsibus0 target 1 lun 0: <IBM-ESXS, MAX3073NC     FN, CA06> disk fix=
ed
sd1: 70006 MB, 49158 cyl, 4 head, 729 sec, 512 bytes/sect x 143374000 secto=
rs
sd1: sync (6.25ns offset 127), 16-bit (320.000MB/s) transfers, tagged queue=
ing
ses0 at scsibus0 target 8 lun 0: <IBM, 25P3495a S320  1, 1> processor fixed
ses0: SAF-TE Compliant Device
ses0: async, 8-bit transfers
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
cpu2: prelint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu2: prelint1 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu2: timer0 200c0<vector=3Dc0,delmode=3D0,dest=3D0> 0<target=3D0>
cpu2: pcint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu2: lint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu2: lint1 400<vector=3D0,delmode=3D4,dest=3D0> 0<target=3D0>
cpu2: err0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu2: CPU 1 running
cpu1: prelint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu1: prelint1 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu1: timer0 200c0<vector=3Dc0,delmode=3D0,dest=3D0> 0<target=3D0>
cpu1: pcint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu1: lint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu1: lint1 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu1: err0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu1: CPU 6 running
cpu3: prelint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu3: prelint1 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu3: timer0 200c0<vector=3Dc0,delmode=3D0,dest=3D0> 0<target=3D0>
cpu3: pcint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu3: lint0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu3: lint1 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu3: err0 10000<vector=3D0,delmode=3D0,masked,dest=3D0> 0<target=3D0>
cpu3: CPU 7 running
wsdisplay0: screen 0 added (80x50, vt100 emulation)
wsdisplay0: screen 1 added (80x50, vt100 emulation)
wsdisplay0: screen 2 added (80x50, vt100 emulation)
wsdisplay0: screen 3 added (80x50, vt100 emulation)
wsdisplay0: screen 4 added (80x50, vt100 emulation)
wsdisplay0: screen 5 added (80x50, vt100 emulation)
wsdisplay0: screen 6 added (80x25, vt100 emulation)
wsdisplay0: screen 7 added (80x25, vt100 emulation)
bge0: pcie mode=3D0x105000


--=20
						Greg A. Woods

H:+1 416 218-0098 W:+1 416 489-5852 x122 VE3TCP RoboHack <woods@robohack.ca>
Planix, Inc. <woods@planix.com>       Secrets of the Weird <woods@weird.com>

--pgp-sign-Multipart_Thu_Sep__6_15:24:33_2007-1
Content-Type: application/pgp-signature
Content-Transfer-Encoding: 7bit

-----BEGIN PGP SIGNATURE-----
Version: PGPfreeware 5.0i for non-commercial use
MessageID: yRNX0VDvLTtoMHlMQ8DaBayzl5iV5XFG

iQA/AwUBRuBT8WZ9cbd4v/R/EQJYVgCgzTXL8OIVAm8s9f3tr4Pdsa4uAakAniBN
QjWipYkdH1fXdjS879WzfbbK
=5Jqs
-----END PGP SIGNATURE-----

--pgp-sign-Multipart_Thu_Sep__6_15:24:33_2007-1--