Hello.  I hav a NetBSD-4_RC2 system, with kernel from the 20071001
snapshot, and 3.0 userland.  It has a new Atheros minicci card in it,
product ID 0x001a, and I'm trying to get it to work.
	Although the card seems to be recognized, and I can see apps around
me, I can't seem to associate with any of them.  Turning on hw.ath0.debug
with sysctl shows me it's discarding a lot of AUTH packets.  My wireless
access point is not using encryption and is not restricting access based on
mac address.  Any ideas?  Do I need to use sysctl to turn off some sort of
authorization sequence that the 80211 link layer protocol is trying to
impose?

Any thoughts would be greatly appreciated.

-Brian

ath0 at pci1 dev 3 function 0LNKB: Picked IRQ 9 with weight 0
ath0: interrupting at irq 9
ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
ath0: mac 7.8 phy 4.5 radio 5.6

#ifconfig ath0
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
	ssid ""
	powersave off
	address: 00:14:78:56:XX:XX
	media: IEEE802.11 autoselect (OFDM54 mode 11g)
	status: no network
	inet 157.22.230.25 netmask 0xffffff00 broadcast 157.22.230.255
	inet6 fe80::214:78ff:fe56:29a0%ath0 prefixlen 64 scopeid 0x2

#wiconfig ath0 -D
scanning ......
AP Information
ap[0]:
	netname (SSID):			[ ringnet ]
	BSSID:				[ 00:11:93:0d:XX:XX ]
	Channel:			[ 11 ]
	Quality/Signal/Noise [signal]:	[ 0 / 19 / 0 ]
	                        [dBm]:	[ 0 / -130 / -149 ]
	BSS Beacon Interval [msec]:	[ 100 ]
	Capinfo:			[ ESS ]
	DataRate [Mbps]:		[ 11 ]
ap[1]:
	netname (SSID):			[ 2WIRE882 ]
	BSSID:				[ 00:19:e4:b8:XX:XX ]
	Channel:			[ 1 ]
	Quality/Signal/Noise [signal]:	[ 0 / 29 / 0 ]
	                        [dBm]:	[ 0 / -120 / -149 ]
	BSS Beacon Interval [msec]:	[ 100 ]
	Capinfo:			[ ESS WEP ]
	DataRate [Mbps]:		[ 11 ]
ap[2]:
	netname (SSID):			[ 2WIRE350 ]
	BSSID:				[ 00:d0:9e:ec:XX:XX ]
	Channel:			[ 6 ]
	Quality/Signal/Noise [signal]:	[ 0 / 5 / 0 ]
	                        [dBm]:	[ 0 / -144 / -149 ]
	BSS Beacon Interval [msec]:	[ 100 ]
	Capinfo:			[ ESS WEP ]
	DataRate [Mbps]:		[ 11 ]
ap[3]:
	netname (SSID):			[ Kingstreet ]
	BSSID:				[ 00:18:39:46:XX:Xx ]
	Channel:			[ 6 ]
	Quality/Signal/Noise [signal]:	[ 0 / 0 / 0 ]
	                        [dBm]:	[ 0 / -149 / -149 ]
	BSS Beacon Interval [msec]:	[ 100 ]
	Capinfo:			[ ESS WEP ]
	DataRate [Mbps]:		[ 11 ]
ap[4]:
	netname (SSID):			[ linksys ]
	BSSID:				[ 00:1c:10:9c:XX:XX ]
	Channel:			[ 6 ]
	Quality/Signal/Noise [signal]:	[ 0 / 11 / 0 ]
	                        [dBm]:	[ 0 / -138 / -149 ]
	BSS Beacon Interval [msec]:	[ 100 ]
	Capinfo:			[ ESS ]
	DataRate [Mbps]:		[ 11 ]