Re: Hard lockup with 4.0 RC5

To: port-i386%netbsd.org@localhost
Subject: Re: Hard lockup with 4.0 RC5
From: Pierre Pronchery <khorben%defora.org@localhost>
Date: Wed, 25 Jun 2008 11:45:50 +0000 (UTC)
On 2008-06-24, Matthias Scheler <tron%zhadum.org.uk@localhost> wrote:
> On 24 Jun 2008, at 3:02, Pierre Pronchery wrote:
>> Interestingly, Linux works by default on the same hardware, regardless
>> of the BIOS settings (vanilla 2.4.36.2 as Debian etch 2.6.18-6-686).
>
> Do you know whether Linux uses ACPI on your system? Linux refuses to use
> ACPI on system with a BIOS released before a certain point of time.
> It might be doing that on your system, too.

Yes it does, and here is the dmesg:

Linux version 2.4.36.2 (root@pinge) (gcc version 4.1.2 20061115 (prerelease) 
(Debian 4.1.1-21)) #5 Sat Apr 19 16:53:22 CEST 2008
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000003fffc000 (usable)
 BIOS-e820: 000000003fffc000 - 000000003ffff000 (ACPI data)
 BIOS-e820: 000000003ffff000 - 0000000040000000 (ACPI NVS)
 BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
 BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
 BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
found SMP MP-table at 000f54d0
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
hm, page 000f5000 reserved twice.
hm, page 000f6000 reserved twice.
On node 0 totalpages: 262140
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32764 pages.
ACPI: RSDP (v000 ASUS                                      ) @ 0x000f6910
ACPI: RSDT (v001 ASUS   CUV4X-D  0x30303031 MSFT 0x31313031) @ 0x3fffc000
ACPI: FADT (v001 ASUS   CUV4X-D  0x30303031 MSFT 0x31313031) @ 0x3fffc100
ACPI: BOOT (v001 ASUS   CUV4X-D  0x30303031 MSFT 0x31313031) @ 0x3fffc040
ACPI: MADT (v001 ASUS   CUV4X-D  0x30303031 MSFT 0x31313031) @ 0x3fffc080
ACPI: DSDT (v001   ASUS CUV4X-D  0x00001000 MSFT 0x0100000b) @ 0x00000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x03] enabled)
Processor #3 Pentium(tm) Pro APIC version 17
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Using ACPI (MADT) for SMP configuration information
Kernel command line: root=/dev/hda3 ro
Initializing CPU#0
Detected 1004.552 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 2005.40 BogoMIPS
Memory: 1033892k/1048560k available (1155k kernel code, 14280k reserved, 431k 
data, 108k init, 131056k highmem)
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU:     After generic, caps: 0383fbff 00000000 00000000 00000000
CPU:             Common caps: 0383fbff 00000000 00000000 00000000
CPU: Intel Pentium III (Coppermine) stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000004
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
 IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22, 2-23 not 
connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1004.4869 MHz.
..... host bus clock speed is 133.9313 MHz.
cpu: 0, clocks: 1339313, slice: 669656
CPU0<T0:1339312,T1:669648,D:8,S:669656,C:1339313>
mtrr: v1.40 (20010327) Richard Gooch (rgooch%atnf.csiro.au@localhost)
mtrr: detected mtrr type: Intel
ACPI: Subsystem revision 20040326
PCI: PCI BIOS revision 2.10 entry at 0xf0d20, last bus=1
PCI: Using configuration type 1
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: System [ACPI] (supports S0 S1 S4 S5)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Via IRQ fixup
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
00:00:04[A] -> 2-11 -> IRQ 11 level low
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
00:00:04[B] -> 2-10 -> IRQ 10 level low
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
00:00:0c[A] -> 2-16 -> IRQ 16 level low
00:00:0c[B] -> 2-17 -> IRQ 17 level low
00:00:0c[C] -> 2-18 -> IRQ 18 level low
00:00:0c[D] -> 2-19 -> IRQ 19 level low
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................

IO APIC #2......
.... register #00: 02000000
.......    : physical APIC id: 02
.......    : Delivery Type: 0
.......    : LTS          : 0
.... register #01: 00178011
.......     : max redirection entries: 0017
.......     : PRQ implemented: 1
.......     : IO APIC version: 0011
.... register #02: 00000000
.......     : arbitration: 00
.... IRQ redirection table:
 NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:   
 00 000 00  1    0    0   0   0    0    0    00
 01 001 01  0    0    0   0   0    1    1    39
 02 001 01  0    0    0   0   0    1    1    31
 03 001 01  0    0    0   0   0    1    1    41
 04 001 01  0    0    0   0   0    1    1    49
 05 001 01  0    0    0   0   0    1    1    51
 06 001 01  0    0    0   0   0    1    1    59
 07 001 01  0    0    0   0   0    1    1    61
 08 001 01  0    0    0   0   0    1    1    69
 09 001 01  0    1    0   1   0    1    1    71
 0a 001 01  1    1    0   1   0    1    1    79
 0b 001 01  1    1    0   1   0    1    1    81
 0c 001 01  0    0    0   0   0    1    1    89
 0d 001 01  0    0    0   0   0    1    1    91
 0e 001 01  0    0    0   0   0    1    1    99
 0f 001 01  0    0    0   0   0    1    1    A1
 10 001 01  1    1    0   1   0    1    1    A9
 11 001 01  1    1    0   1   0    1    1    B1
 12 001 01  1    1    0   1   0    1    1    B9
 13 001 01  1    1    0   1   0    1    1    C1
 14 000 00  1    0    0   0   0    0    0    00
 15 000 00  1    0    0   0   0    0    0    00
 16 000 00  1    0    0   0   0    0    0    00
 17 000 00  1    0    0   0   0    0    0    00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
.................................... done.
PCI: Using ACPI for IRQ routing
PCI: Enabling Via external APIC routing
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch%atnf.csiro.au@localhost)
devfs: boot_options: 0x1
pty: 256 Unix98 ptys configured
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 00:04.1
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: VIA vt82c686b (rev 40) IDE UDMA100 controller on pci00:04.1
    ide0: BM-DMA at 0xb800-0xb807, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xb808-0xb80f, BIOS settings: hdc:pio, hdd:DMA
hda: WDC WD800BB-00JHC0, ATA DISK drive
hdd: HL-DT-STDVD-ROM GDR8164B, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=9729/255/63, UDMA(100)
Partition check:
 /dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 >
 p1: <netbsd: p6 p7 p8 p9 p10 >
 p2: <netbsd: p11 p12 p13 p14 p15 >
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
kjournald starting.  Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 108k freed
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Adding Swap: 497972k swap-space (priority -1)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,3), internal journal
Real Time Clock Driver v1.10f
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 16:30:46 Apr 19 2008
usb-uhci.c: High bandwidth mode enabled
usb-uhci.c: USB UHCI at I/O 0xb400, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: USB UHCI at I/O 0xb000, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
SCSI subsystem driver Revision: 1.00
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI 
ISAPNP enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
via-rhine.c:v1.10-LK1.1.19  July-12-2003  Written by Donald Becker
  http://www.scyld.com/network/via-rhine.html
eth0: VIA VT6105 Rhine-III at 0xa400, 00:40:f4:7c:c5:34, IRQ 17.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
eth0: Setting full-duplex based on MII #1 link partner capability of 45e1.
802.1Q VLAN Support v1.8 Ben Greear <greearb%candelatech.com@localhost>
All bugs added by David S. Miller <davem%redhat.com@localhost>
eth0.3: add 01:00:5e:00:00:01 mcast address to master interface
ACPI: Processor [CPU] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Power Button (FF) [PWRF]
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport_pc: Via 686A parallel port: io=0x378
lp0: using parport0 (polling).
ppdev: user-space parallel port driver
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: Detected Via Apollo Pro chipset
agpgart: AGP aperture is 256M @ 0xe0000000
[drm] AGP 0.99 Aperture @ 0xe0000000 256MB
[drm] Initialized radeon 1.8.0 20020828 on minor 0
[drm] Loading R200 Microcode

-- 
khorben
References:
- Re: Hard lockup with 4.0 RC5
  - From: Pierre Pronchery
- Re: Hard lockup with 4.0 RC5
  - From: Matthias Scheler
Prev by Date: Re: Hard lockup with 4.0 RC5
Next by Date: mpacpi broken (again) on -current
Previous by Thread: Re: Hard lockup with 4.0 RC5
Next by Thread: mpacpi broken (again) on -current
Indexes:
Home | Main Index | Thread Index | Old Index