HP Pavilion zv5000 won't boot from 7.0 install image

[Ray Phillips <ray.phillips%gmail.com@localhost>]

My HP Pavilion zv5000 laptop will boot from a USB key which has had
the (decompressed) NetBSD-6.1.5-i386-install.img.gz copied to it using
dd.  The output of dmesg after it has booted is shown below.  However,
it won't boot using NetBSD-7.0-i386-install.img.  When I choose option
1 from the boot menu (ACPI and SMP) the boot process freezes after
these last few lines:

isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: failed to evaluate _PCT: AE_AML_BAD_RESOURCE_VALUE
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0

and when the boot option with no ACPI and no SMP is selected it
freezes after these lines:

isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbc: cmd word write error
attimer0 at isa0 port 0x40-0x43
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
attimer0: attached to pcppi0

so I haven't been able to upgrade this machine to NetBSD 7.0.  Could
someone suggest a solution please?


Ray



Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 6.1.5 (GENERIC)
total memory = 1919 MB
avail memory = 1874 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
Hewlett-Packard  Pavilion zv5000 (DV534PA#ABG)  (F.45)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Mobile Intel(R) Pentium(R) 4     CPU 3.06GHz, id 0xf29
ioapic0 at mainbus0 apid 1: pa 0xfec00000, version 11, 24 pins
acpi0 at mainbus0: Intel ACPICA 20110623
acpi0: X/RSDT: OemId <PTLTD ,  RSDT  ,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
acpiec0 at acpi0 (EC0, PNP0C09): io 0x62,0x66
acpiwmi0 at acpi0 (WMID, PNP0C14-0): ACPI WMI Interface
acpiwmibus at acpiwmi0 not configured
acpilid0 at acpi0 (LID, PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
acpivga0 at acpi0 (VGA): ACPI Display Adapter
acpiout0 at acpivga0 (CRT, 0x0100): ACPI Display Output Device
acpiout1 at acpivga0 (LCD, 0x0110): ACPI Display Output Device
acpiout2 at acpivga0 (TV, 0x0200): ACPI Display Output Device
acpivga0: connected output devices:
acpivga0:   0x0100 (acpiout0): Ext. Monitor, head 0, bios detect
acpivga0:   0x0110 (acpiout1): LCD Panel, head 0, bios detect
acpivga0:   0x0200 (acpiout2): TV, head 0
npx1 at acpi0 (MATH, PNP0C04): io 0xf0-0xfe irq 13
npx1: reported by CPUID; using exception 16
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker
sysbeep0 at pcppi1
attimer1 at acpi0 (TIME, PNP0100): io 0x40-0x43 irq 0
pckbc1 at acpi0 (KBC0, PNP0303) (kbd port): io 0x60,0x64 irq 1
pckbc2 at acpi0 (MSE0, PNP0F13) (aux port): irq 12
SYSR (PNP0C02) at acpi0 not configured
ECP1 (PNP0401) at acpi0 not configured
acpiacad0 at acpi0 (ACAD, ACPI0003): ACPI AC Adapter
acpibat0 at acpi0 (BAT1, PNP0C0A-1): ACPI Battery
acpitz0 at acpi0 (THRM)
acpitz0: levels: critical 82.0 C, passive cooling
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: vendor 0x1002 product 0x5833 (rev. 0x02)
agp at pchb0 not configured
ppb0 at pci0 dev 1 function 0: vendor 0x1002 product 0x5838 (rev. 0x00)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 5 function 0: vendor 0x1002 product 0x5835 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
radeondrm0 at vga1: ATI Radeon RS300 Mobility IGP
radeondrm0: Initialized radeon 1.29.0 20080613
ohci0 at pci0 dev 19 function 0: vendor 0x1002 product 0x4347 (rev. 0x01)
ohci0: interrupting at ioapic0 pin 19
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 19 function 1: vendor 0x1002 product 0x4348 (rev. 0x01)
ohci1: interrupting at ioapic0 pin 19
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
piixpm0 at pci0 dev 20 function 0: vendor 0x1002 product 0x4353 (rev. 0x16)
piixpm0: interrupting at SMI, polling
iic0 at piixpm0: I2C bus
ixpide0 at pci0 dev 20 function 1: ATI Technologies IXP IDE Controller
(rev. 0x00)
ixpide0: bus-master DMA support present
ixpide0: primary channel configured to compatibility mode
ixpide0: primary channel interrupting at ioapic0 pin 14
atabus0 at ixpide0 channel 0
ixpide0: secondary channel configured to compatibility mode
ixpide0: secondary channel interrupting at ioapic0 pin 15
atabus1 at ixpide0 channel 1
pcib0 at pci0 dev 20 function 3: vendor 0x1002 product 0x434c (rev. 0x00)
ppb1 at pci0 dev 20 function 4: vendor 0x1002 product 0x4342 (rev. 0x00)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
fwohci0 at pci2 dev 0 function 0: vendor 0x104c product 0x8026 (rev. 0x00)
fwohci0: interrupting at ioapic0 pin 16
fwohci0: OHCI version 1.10 (ROM=0)
fwohci0: No. of Isochronous channels is 4.
fwohci0: EUI64 3c:3f:02:00:68:a1:00:3d
fwohci0: Phy 1394a available S400, 1 ports.
fwohci0: Link S400, max_rec 2048 bytes.
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
rtk0 at pci2 dev 3 function 0: Realtek 8139 10/100BaseTX (rev. 0x10)
rtk0: interrupting at ioapic0 pin 19
rtk0: Ethernet address 00:02:3f:6a:d3:cb
rlphy0 at rtk0 phy 7: Realtek internal PHY
rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
cbb0 at pci2 dev 4 function 0: vendor 0x104c product 0xac54 (rev. 0x01)
cbb1 at pci2 dev 4 function 1: vendor 0x104c product 0xac54 (rev. 0x01)
vendor 0x104c product 0x8201 (miscellaneous system, revision 0x01) at
pci2 dev 4 function 2 not configured
ohci2 at pci2 dev 7 function 0: vendor 0x1033 product 0x0035 (rev. 0x43)
ohci2: interrupting at ioapic0 pin 16
ohci2: OHCI version 1.0, legacy support
usb2 at ohci2: USB revision 1.0
ohci3 at pci2 dev 7 function 1: vendor 0x1033 product 0x0035 (rev. 0x43)
ohci3: interrupting at ioapic0 pin 18
ohci3: OHCI version 1.0, legacy support
usb3 at ohci3: USB revision 1.0
ehci0 at pci2 dev 7 function 2: vendor 0x1033 product 0x00e0 (rev. 0x04)
ehci0: interrupting at ioapic0 pin 19
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci2 ohci3
usb4 at ehci0: USB revision 2.0
cbb0: cacheline 0x8 lattimer 0x40
cbb0: bhlc 0x824008
cbb0: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb0: interrupting at ioapic0 pin 17
cardslot0 at cbb0
pcmcia0 at cardslot0
cbb1: cacheline 0x8 lattimer 0x40
cbb1: bhlc 0x824008
cbb1: secondary bus number uninitialized; try PCI_BUS_FIXUP
cbb1: interrupting at ioapic0 pin 16
cardslot1 at cbb1
pcmcia1 at cardslot1
auixp0 at pci0 dev 20 function 5: vendor 0x1002 product 0x4341 (rev. 0x00)
auixp0: interrupting at ioapic0 pin 5
auixp0: soft resetting aclink
vendor 0x1002 product 0x434d (modem communications, revision 0x01) at
pci0 dev 20 function 6 not configured
isa0 at pcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
acpicpu0 at cpu0: ACPI CPU
acpicpu0: failed to evaluate _PCT: AE_AML_BAD_RESOURCE_VALUE
acpicpu0: C1: HLT, lat   0 us, pow     0 mW
acpicpu0: C2: I/O, lat  18 us, pow     0 mW
acpicpu0: P0: ???, lat 250 us, pow     0 mW, 3059 MHz
acpicpu0: P1: ???, lat 250 us, pow     0 mW, 1596 MHz
fwohci0: BUS reset
fwohci0: node_id=0xc000ffc0, gen=1, CYCLEMASTER mode
ieee1394if0: 1 nodes, maxhop <= 0 cable IRM irm(0) (me)
ieee1394if0: bus manager 0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
auixp0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D stereo
auixp0: ac97: ext id 0x605<AC97_22,AMAP,SPDIF,VRA>
auixp0: ac97: Silicon Laboratory unknown (0x53494c27) codec; no 3D stereo
auixp0: codec spdif support detected but disabled for now
audio0 at auixp0: full duplex, playback, capture, mmap, independent
audio1 at auixp0: full duplex, playback, capture, mmap, independent
acpiec0: command takes over 10 sec...
ACPI Exception: AE_ERROR, Returned by Handler for [EmbeddedControl]
(20110623/evregion-522)
ACPI Error: Method parse/execution failed [\_SB_.PCI0.LPC0.ACAD._PSR]
(Node 0xc33cc024), AE_ERROR (20110623/psparse-560)
uhub0 at usb0: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x1002 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
uhub2 at usb2: vendor 0x1033 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 3 ports with 3 removable, self powered
uhub3 at usb3: vendor 0x1033 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x1033 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub4: 5 ports with 5 removable, self powered
umass0 at uhub4 port 1 configuration 1 interface 0
umass0: JetFlash Mass Storage Device, rev 2.00/1.41, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <JetFlash, TS4GJFV30, 8.07> disk removable
sd0: fabricating a geometry
sd0: 3911 MB, 3911 cyl, 64 head, 32 sec, 512 bytes/sect x 8011774 sectors
sd0: fabricating a geometry
wd0 at atabus0 drive 0
wd0: <SAMSUNG HM160HC>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310101 cyl, 16 head, 63 sec, 512 bytes/sect x 312581808 sectors
uhub5 at uhub4 port 5: NEC Corporation USB2.0 Hub Controller, class
9/0, rev 2.00/1.00, addr 3
uhub5: single transaction translator
uhub5: 4 ports with 3 removable, self powered
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ixpide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
acpibat0: normal capacity on 'charge state'
uhub5: device problem, disabling port 1
uhub6 at uhub5 port 4: NEC Corporation USB2.0 Hub Controller, class
9/0, rev 2.00/1.00, addr 4
uhub6: single transaction translator
uhub6: 3 ports with 3 removable, self powered
Kernelized RAIDframe activated
boot device: sd0
root on sd0a dumps on sd0b
root file system type: ffs
WARNING: clock gained 434 days