Hello guys,
I used NetBSD-5 branch and X didn't start.
That's Xorg.0.log tail
I then reverted to NetBSD-5-Base and it works.
I searched the documentation about the pms driver but I couldn't compile a kernel with it.
The documentation I found have i386 examples like:
pms* at pckbc? # PS/2-style mouse (aux port)
but doesn't seem to be any pckbc device in dmesg, and build fails:
622: pms*: unknown device `pms'
I installed bwi patch to enable the airport, and the driver compiled all right too, but I am not in a wireless network to test now.
I got the packages here: http://people.csail.mit.edu/riastradh/nbsd/
what about the backlit keyboard light and brightness control ?
is there a driver for that ?
Thanks a lot.
That's dmesg with NetBSD-5 branch:
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
 2006, 2007, 2008
 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
 The Regents of the University of California. All rights reserved.
NetBSD 5.0_RC2 (millenium_falcon) #2: Mon Feb 23 11:19:56 BRT 2009
Âisrael@millenium_falcon:/usr/obj/sys/arch/macppc/compile/millenium_falcon
total memory = 2048 MB
avail memory = 1980 MB
timecounter: Timecounters tick every 10.000 msec
found openpic PIC at 80040000
OpenPIC Version 1.2: Supports 4 CPUs and 64 interrupt sources.
bootpath: /pci@f4000000/ata-6@d/disk@0:5,/netbsd
mainbus0 (root)
cpu0 at mainbus0: 7447A (Revision 1.5), ID 0 (primary)
cpu0: HID0 8450c0bc<EMCP,EICE,NAP,DPM,ICE,DCE,SGE,BTIC,FBIOB,ABE,BHT>, powersave: 1
cpu0: 833.33 MHz, 512KB L2 cache no parity parity enabled
memory0 at mainbus0: len=256
spdmem0 at memory0
spdmem0: DDR2 SDRAM memory, no parity or ECC, 1024MB, 533MHz (PC2-4300)
spdmem0: 14 rows, 10 cols, 2 ranks, 4 banks/chip, 3.75ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 5-4-4-12
spdmem0: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
spdmem1 at memory0
spdmem1: DDR2 SDRAM memory, no parity or ECC, 1024MB, 533MHz (PC2-4300)
spdmem1: 14 rows, 10 cols, 2 ranks, 4 banks/chip, 3.75ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 5-4-4-12
spdmem1: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
uni_n0 at mainbus0 address 0xf8000000
hw-clock at uni_n0 not configured
ki2c0 at uni_n0 address 0xf8001000
iic1 at ki2c0: I2C bus
dbcool0 at ki2c0
dbcool0: ADT7467/ADT7468 dBCool(tm) Controller (rev 0x07, stepping 0x01)
temp-monitor at ki2c0 address 0x92 not configured
uninorth0 at mainbus0
pci0 at uninorth0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer Intrepid 2 AGP (rev. 0x00)
genfb0 at pci0 dev 16 function 0: ATI Technologies Radeon Mobility 9600/9700 (M10/11) NP
genfb0: framebuffer at 0xb8008000, size 1680x1050, depth 8, stride 1792
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at genfb0 not configured
uninorth1 at mainbus0
pci1 at uninorth1 bus 0
pci1: i/o space, memory space enabled
pchb1 at pci1 dev 11 function 0
pchb1: Apple Computer Intrepid 2 PCI (rev. 0x00)
Broadcom BCM4318 AirForce One 54g (miscellaneous network, revision 0x02) at pci1 dev 17 function 0 not configured
cbb0 at pci1 dev 20 function 0: Texas Instruments PCI1510 PCI-CardBus Bridge (rev. 0x00)
ohci0 at pci1 dev 21 function 0: NEC USB Host Controller (rev. 0x43)
ohci0: interrupting at irq 54
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci1 at pci1 dev 21 function 1: NEC USB Host Controller (rev. 0x43)
ohci1: interrupting at irq 54
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
ehci0 at pci1 dev 21 function 2: NEC USB Host Controller (rev. 0x04)
ehci0: interrupting at irq 54
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
obio0 at pci1 dev 23 function 0: addr 0x80000000
zsc0 at obio0 irq 22,23
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
i2s at obio0 offset 0x0 not configured
pmu0 at obio0 offset 0x16000 irq 47: rev. 17
pmu0: initializing IIC bus
pmu0: initializing RTC
pmu0: pmu not configured
pmu0: power-mgt not configured
smartbat0 at pmu0 addr 0: smart battery
Âflags: 5 AC present
ki2c1 at obio0
iic2 at ki2c1: I2C bus
codec at ki2c1 address 0x8c not configured
codec at ki2c1 address 0x20 not configured
cbb0: cacheline 0x8 lattimer 0x10
cbb0: bhlc 0x21008
cbb0: interrupting at irq 53
cardslot0 at cbb0
cardbus0 at cardslot0: bus 1
pcmcia0 at cardslot0
uninorth2 at mainbus0
pci2 at uninorth2 bus 0
pci2: i/o space, memory space enabled
pchb2 at pci2 dev 11 function 0
pchb2: Apple Computer Intrepid 2 PCI (rev. 0x00)
wdc0 at pci2 dev 13 function 0: interrupting at irq 39
atabus0 at wdc0 channel 0
fwohci0 at pci2 dev 14 function 0: Apple Computer Intrepid 2 FireWire (rev. 0x00)
fwohci0: interrupting at irq 40
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:11:24:ff:fe:d6:40:5c
fwohci0: fwphy_rddata: 0x2 loop=100, retry=100
fwohci0: Phy 1394 only S100, 0 ports.
fwohci0: fwphy_rddata: 0x2 loop=100, retry=100
fwohci0: Link S800, max_rec 4096 bytes.
fwohci0: max_rec 4096 -> 512
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=100, retry=100
fwohci0: fwphy_rddata: 0x1 loop=100, retry=100
gem0 at pci2 dev 15 function 0: Apple Computer Intrepid 2 GMAC (rev. 0x00)
gem0: interrupting at irq 41
ukphy0 at gem0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x001018, model 0x000d, rev. 3
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ukphy1 at gem0 phy 1: Generic IEEE 802.3u media interface
ukphy1: OUI 0x604112, model 0x0031, rev. 10
ukphy1:Â
gem0: cannot accommodate MII device ukphy1 at PHY 1, instance 1
gem0: Ethernet address 00:11:24:d6:40:5c, 10KB RX fifo, 4KB TX fifo
biomask 80001fe netmask 80001fe ttymask 80001fe
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mftb" frequency 8320000 Hz quality 100
uhub0 at usb0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <MATSHITADVD-R UJ-846, , FAAG> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0 at atabus0 drive 0: <ST9120821A>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 111 GB, 232581 cyl, 16 head, 63 sec, 512 bytes/sect x 234441648 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
cd0(wdc0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) (using DMA)
AC Power: AC adapter online.
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: vendor 0x15d9 USB Mouse, rev 1.10/1.00, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
Kernelized RAIDframe activated
uhidev1 at uhub0 port 2 configuration 1 interface 0
uhidev1: Apple Computer product 0x1000, rev 2.00/19.65, addr 2, iclass 3/1
boot device: wd0
root on wd0a dumps on wd0b
ukbd0 at uhidev1
root file system type: ffs
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev2 at uhub0 port 2 configuration 1 interface 1
uhidev2: Apple Computer product 0x1000, rev 2.00/19.65, addr 2, iclass 3/1
ums1 at uhidev2: 5 buttons
wsmouse1 at ums1 mux 0
uhidev3 at uhub1 port 2 configuration 1 interface 0
uhidev3: Apple Computer Apple Internal Keyboard / Trackpad, rev 2.00/0.86, addr 3, iclass 3/1
ukbd1 at uhidev3
wskbd1 at ukbd1 mux 1
wskbd1: connecting to wsdisplay0
uhidev4 at uhub1 port 2 configuration 1 interface 1
uhidev4: Apple Computer Apple Internal Keyboard / Trackpad, rev 2.00/0.86, addr 3, iclass 3/1
uhid0 at uhidev4: input=64, output=0, feature=16
uhidev5 at uhub1 port 2 configuration 1 interface 2
uhidev5: Apple Computer Apple Internal Keyboard / Trackpad, rev 2.00/0.86, addr 3, iclass 3/0
uhid1 at uhidev5: input=1, output=0, feature=0
/dev/wd0a: file system not clean (fs_clean=0); please fsck(8)
/dev/wd0a: lost blocks 0 files 0
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)
/dev/wd0a: file system not clean (fs_clean=0); please fsck(8)
/dev/wd0a: lost blocks 0 files 0
--------------------------------------------------------------------------------------------------------------
dmesg with the NetBSD-5-Base branch
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
 2006, 2007, 2008
 The NetBSD Foundation, Inc. All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
 The Regents of the University of California. All rights reserved.
NetBSD 4.99.73 (millenium_falcon) #3: Mon Feb 23 22:05:37 BRT 2009
Âisrael@millenium_falcon:/usr/obj/sys/arch/macppc/compile/millenium_falcon
total memory = 2048 MB
avail memory = 1980 MB
timecounter: Timecounters tick every 10.000 msec
found openpic PIC at 80040000
OpenPIC Version 1.2: Supports 4 CPUs and 64 interrupt sources.
bootpath: /pci@f4000000/ata-6@d/disk@0:5,/netbsd
mainbus0 (root)
cpu0 at mainbus0: 7447A (Revision 1.5), ID 0 (primary)
cpu0: HID0 8450c0bc<EMCP,EICE,NAP,DPM,ICE,DCE,SGE,BTIC,FBIOB,ABE,BHT>, powersave: 1
cpu0: 833.34 MHz, 512KB L2 cache no parity parity enabled
memory0 at mainbus0len: 256
spdmem0 at memory0
spdmem0: DDR2 SDRAM memory, no parity or ECC, 1024MB, 533MHz (PC2-4300)
spdmem0: 14 rows, 10 cols, 2 ranks, 4 banks/chip, 3.75ns cycle time
spdmem0: tAA-tRCD-tRP-tRAS: 5-4-4-12
spdmem0: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
spdmem1 at memory0
spdmem1: DDR2 SDRAM memory, no parity or ECC, 1024MB, 533MHz (PC2-4300)
spdmem1: 14 rows, 10 cols, 2 ranks, 4 banks/chip, 3.75ns cycle time
spdmem1: tAA-tRCD-tRP-tRAS: 5-4-4-12
spdmem1: voltage SSTL 1.8V, refresh time 7.8us (self-refreshing)
uni_n0 at mainbus0 address 0xf8000000
hw-clock at uni_n0 not configured
ki2c0 at uni_n0 address 0xf8001000
iic1 at ki2c0: I2C bus
dbcool0 at ki2c0
dbcool0: ADT7467/ADT7468 dBCool(tm) Controller (rev 0x07, stepping 0x01)
temp-monitor at ki2c0 address 0x92 not configured
uninorth0 at mainbus0
pci0 at uninorth0 bus 0
pci0: i/o space, memory space enabled
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer Intrepid 2 AGP (rev. 0x00)
genfb0 at pci0 dev 16 function 0: ATI Technologies Radeon Mobility 9600/9700 (M10/11) NP
genfb0: framebuffer at 0xb8008000, size 1680x1050, depth 8, stride 1792
wsdisplay0 at genfb0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
drm at genfb0 not configured
uninorth1 at mainbus0
pci1 at uninorth1 bus 0
pci1: i/o space, memory space enabled
pchb1 at pci1 dev 11 function 0
pchb1: Apple Computer Intrepid 2 PCI (rev. 0x00)
bwi0 at pci1 dev 17 function 0
bwi0: interrupting at irq 52
bwi0: BBP id 0x4318, BBP rev 0x2, BBP pkg 2
bwi0: MAC: rev 9
bwi0: PHY type 2, rev 7, ver 3
bwi0: RF manu 0x17f, type 0x2050, rev 8
bwi0: invalid antenna gain in sprom
bwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
bwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
cbb0 at pci1 dev 20 function 0: Texas Instruments PCI1510 PCI-CardBus Bridge (rev. 0x00)
ohci0 at pci1 dev 21 function 0: NEC USB Host Controller (rev. 0x43)
ohci0: interrupting at irq 54
ohci0: OHCI version 1.0
usb0 at ohci0: USB revision 1.0
ohci1 at pci1 dev 21 function 1: NEC USB Host Controller (rev. 0x43)
ohci1: interrupting at irq 54
ohci1: OHCI version 1.0
usb1 at ohci1: USB revision 1.0
ehci0 at pci1 dev 21 function 2: NEC USB Host Controller (rev. 0x04)
ehci0: interrupting at irq 54
ehci0: EHCI version 1.0
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
obio0 at pci1 dev 23 function 0: addr 0x80000000
zsc0 at obio0: irq 22,23
zstty0 at zsc0 channel 0
zstty1 at zsc0 channel 1
i2s at obio0 offset 0x0 not configured
pmu0 at obio0 offset 0x16000 irq 47: rev. 17
pmu0: initializing IIC bus
pmu0: initializing RTC
pmu0: pmu not configured
pmu0: power-mgt not configured
smartbat0 at pmu0 addr 0: smart battery
Âflags: 5 AC present
ki2c1 at obio0
iic2 at ki2c1: I2C bus
codec at ki2c1 address 0x8c not configured
codec at ki2c1 address 0x20 not configured
cbb0: cacheline 0x8 lattimer 0x10
cbb0: bhlc 0x21008
cbb0: interrupting at irq 53
cardslot0 at cbb0
cardbus0 at cardslot0: bus 1
pcmcia0 at cardslot0
uninorth2 at mainbus0
pci2 at uninorth2 bus 0
pci2: i/o space, memory space enabled
pchb2 at pci2 dev 11 function 0
pchb2: Apple Computer Intrepid 2 PCI (rev. 0x00)
wdc0 at pci2 dev 13 function 0: interrupting at irq 39
atabus0 at wdc0 channel 0
fwohci0 at pci2 dev 14 function 0: Apple Computer Intrepid 2 FireWire (rev. 0x00)
fwohci0: interrupting at irq 40
fwohci0: OHCI version 1.0 (ROM=0)
fwohci0: No. of Isochronous channels is 8.
fwohci0: EUI64 00:11:24:ff:fe:d6:40:5c
fwohci0: fwphy_rddata: 0x2 loop=100, retry=100
fwohci0: Phy 1394 only S100, 0 ports.
fwohci0: fwphy_rddata: 0x2 loop=100, retry=100
fwohci0: Link S800, max_rec 4096 bytes.
fwohci0: max_rec 4096 -> 512
ieee1394if0 at fwohci0: IEEE1394 bus
fwip0 at ieee1394if0: IP over IEEE1394
fwohci0: Initiate bus reset
fwohci0: fwphy_rddata: 0x1 loop=100, retry=100
fwohci0: fwphy_rddata: 0x1 loop=100, retry=100
gem0 at pci2 dev 15 function 0: Apple Computer Intrepid 2 GMAC (rev. 0x00)
gem0: interrupting at irq 41
ukphy0 at gem0 phy 0: Generic IEEE 802.3u media interface
ukphy0: OUI 0x001018, model 0x000d, rev. 3
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
ukphy1 at gem0 phy 1: Generic IEEE 802.3u media interface
ukphy1: OUI 0x604112, model 0x0031, rev. 10
ukphy1:Â
gem0: cannot accommodate MII device ukphy1 at PHY 1, instance 1
gem0: Ethernet address 00:11:24:d6:40:5c, 10KB RX fifo, 4KB TX fifo
biomask 80003fe netmask 80003fe ttymask 80003fe
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "mftb" frequency 8320000 Hz quality 100
uhub0 at usb0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 5 ports with 5 removable, self powered
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 1: <MATSHITADVD-R UJ-846, , FAAG> cdrom removable
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66)
wd0 at atabus0 drive 0: <ST9120821A>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 111 GB, 232581 cyl, 16 head, 63 sec, 512 bytes/sect x 234441648 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(wdc0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100) (using DMA)
cd0(wdc0:0:1): using PIO mode 4, DMA mode 2, Ultra-DMA mode 4 (Ultra/66) (using DMA)
AC Power: AC adapter online.
uhidev0 at uhub1 port 1 configuration 1 interface 0
uhidev0: vendor 0x15d9 USB Mouse, rev 1.10/1.00, addr 2, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse0 at ums0 mux 0
Kernelized RAIDframe activated
uhidev1 at uhub0 port 2 configuration 1 interface 0
uhidev1: Apple Computer product 0x1000, rev 2.00/19.65, addr 2, iclass 3/1
boot device: wd0
root on wd0a dumps on wd0b
ukbd0 at uhidev1
root file system type: ffs
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev2 at uhub0 port 2 configuration 1 interface 1
uhidev2: Apple Computer product 0x1000, rev 2.00/19.65, addr 2, iclass 3/1
ums1 at uhidev2: 5 buttons
wsmouse1 at ums1 mux 0
uhidev3 at uhub1 port 2 configuration 1 interface 0
uhidev3: Apple Computer Apple Internal Keyboard / Trackpad, rev 2.00/0.86, addr 3, iclass 3/1
ukbd1 at uhidev3
wskbd1 at ukbd1 mux 1
wskbd1: connecting to wsdisplay0
uhidev4 at uhub1 port 2 configuration 1 interface 1
uhidev4: Apple Computer Apple Internal Keyboard / Trackpad, rev 2.00/0.86, addr 3, iclass 3/1
uhid0 at uhidev4: input=64, output=0, feature=16
uhidev5 at uhub1 port 2 configuration 1 interface 2
uhidev5: Apple Computer Apple Internal Keyboard / Trackpad, rev 2.00/0.86, addr 3, iclass 3/0
uhid1 at uhidev5: input=1, output=0, feature=0
bwi0: firmware rev 0x0127, patch level 0x000e
wsdisplay0: screen 1 added (default, vt100 emulation)
wsdisplay0: screen 2 added (default, vt100 emulation)
wsdisplay0: screen 3 added (default, vt100 emulation)
wsdisplay0: screen 4 added (default, vt100 emulation)
-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1
Hello,
On Feb 21, 2009, at 9:27 AM, Israel Miranda wrote:Ok, so I do need to look at radeonfb and figure out why it thinks the aperture is only 64MB.
I recompilled the kernel without the radeonfb module and it worked.
- -base is the version the 5.0 branch is based on. Just use netbsd-5. -rc1, -rc2 and so on are tags, not branches.
Now, when I was obtaining the sources to compile the kernel, I was in doubt about which branch to use... netbsd-5-base, netbsd-5-rc1 or netbsd-5-rc2
I choose netbsd-5-base, compiled all right.
Before, my kernel says NETBSD 5 BETA, now it says NetBSD 4.99.73. Is there a problem using an older kernel then the base in pkgsrc ?
Irrelevant, it has its own branches and should work with all recent NetBSD releases and -current.
how do I know which branch pkgsrc is using ?
As I said - neither. Use either HEAD for -current or the netbsd-5 branch.
What do you recommend Âfor source/pkgsrc/ kernel use? netbsd-5-base, netbsd-5-rc1 or netbsd-5-rc2 ?
ooh... sorry for these quesions here too, but I am really lost
Yes, Xorg -configure is still a bit stupid.
At first the keyboard didn' t work, Xorg.0.log yelled to use   Option "Device" "/dev/wskbd0" didnt't work either, so I re-read your other email about it to and used   Option "Device" "/dev/wskbd" and it worked.
Use the pms kernel driver, newer PowerBooks need it for their touchpads.
Touchpad doesn' t work, but I am using an external usb mouse
Yes, my iBook has an rv280 which actually has a 64MB aperture and it works just fine.
Since you didn't say anything about it I guess radeonfb works propely on your machine.
I better keep radeonfb from attaching on this chip. Besides, radeonfb shouldn't be compiled into 5.0 GENERIC and INSTALL kernels anyway, we know it has problems on some radeons.
No, it doesn't ... my installation was unusable with radeonfb. Console screen had a yellow background(very ugly) and the first upper lines weren't working. If the screen rolls down, it worked, but if I open a program like vi , mc or any other with 'full screen', these lines were unreadable. I had no graphical environment and the terminal was 'screwed', so I set sshd and was doing everything remotely
Good.
Now without radeonfb the background is white, it works normally, and X starts.
Yes, you do need the pms driver.
uhidev5: Apple Computer Apple Internal Keyboard / Trackpad, rev 2.00/0.86, addr 3, iclass 3/0
uhid1 at uhidev5: input=1, output=0, feature=0
Alright, no radeonfb for this PCI ID...
(II) PCI: 00:00:0: chip 1002,4e50 card 1002,4e50 rev 00 class 03,00,00 hdr 00
iQEVAwUBSaAn+MpnzkX8Yg2nAQIkyAf/TYgwmZXvE++ppDBiS3P1R0SxMSMZ0CCj
have fun
Michael
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.7 (Darwin)
VqJLoJnha8yE5yuhgKKF5jkeaMiYAFLATPutRw5XznT6Uu/uJO84+9XlIxg3eKrE
wtqJ+99s7mLcp3tb5HJtC/QWPGDmqzaTU3BRBnm0YzYIHPFppP8iazzQW5hs6jvR
DBM03+XyMPsI5eYbzYxpZo7Z3YJu+Xov2yyO1IZHhoQM0p1jYz832/gOTJDnrEw0
m8Mmq8McqqAyrDVMmOK5SaJIbfuzkX8Xk0PCRZHcHF1ehRlvUl3K3MED+KlpwrB9
TyeaCMw9B8uyGhI9R9lXcW7uqqop+TRhUIFIJ6mSL5d8n1PkLBh0ag==
=ARxU
-----END PGP SIGNATURE-----