RE: SGI O2 unable to boot 9.0+ (status update)

To: "'matthew green'" <mrg%eterna23.net@localhost>, <port-mips%netbsd.org@localhost>, "'Andrius V'" <vezhlys%gmail.com@localhost>, <maya%netbsd.org@localhost>, <dholland%netbsd.org@localhost>, "'Mike Shields'" <mike%shieldsworld.com@localhost>
Subject: RE: SGI O2 unable to boot 9.0+ (status update)
From: <iwama%t3.rim.or.jp@localhost>
Date: Wed, 3 Jul 2024 13:13:44 +0900
Hi All,

I have two O2s, an R12000 400MHz and an R5000SC 200MHz.

1)R12000
On my O2, 9.4 boots fine. Both netbsd-GENERIC32_IP3x and
netbsd-INSTALL32_IP3x are OK.
The log when starting a kernel placed in the IRIX file system via sash is as
follows.

> hinv
                   System: IP32
                Processor: 400 Mhz R12000, with FPU
     Primary I-cache size: 32 Kbytes
     Primary D-cache size: 32 Kbytes
     Secondary cache size: 2 Mbytes
              Memory size: 448 Mbytes
                 Graphics: CRM, Rev C
                    Audio: A3 version 1
                SCSI Disk: scsi(0)disk(2)
               SCSI CDROM: scsi(0)cdrom(4)
                SCSI Disk: scsi(1)disk(2)
                SCSI Disk: scsi(1)disk(3)
> version


PROM Monitor (BE)
Tue Oct 22 10:58:00 PDT 2002 
VERSION 4.18
O2 R5K/R7K/R10K/R12K
IRIX 6.5.x IP32prom IP32PROM-v4

> boot -f scsi(1)disk(3)rdisk(0)partition(8)sash
scsi(1)disk(3)rdisk(0)partition(0)NetBSD/netbsd-INSTALL32_IP3x_94
136992+22896+3248+341792+49584d+4620+6880 entry: 0x8ffa5e50
11898512+131872 entry: 0x80069000
[   1.0000000] phys segment: 0x5e000 @ 0x2000
[   1.0000000] adding 0x5e000 @ 0x2000 to freelist 0
[   1.0000000] phys segment: 0xb7a000 @ 0x60000
[   1.0000000] adding 0x6000 @ 0x60000 to freelist 0
[   1.0000000] skipping 0xb74000 @ 0x66000 (kernel)
[   1.0000000] phys segment: 0x176000 @ 0xbda000
[   1.0000000] adding 0x176000 @ 0xbda000 to freelist 0
[   1.0000000] phys segment: 0xeb84000 @ 0x1400000
[   1.0000000] adding 0xeb84000 @ 0x1400000 to freelist 0
[   1.0000000] phys segment: 0x7c000 @ 0xff84000
[   1.0000000] adding 0x7c000 @ 0xff84000 to freelist 0
[   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[   1.0000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012,
2013,
[   1.0000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022,
2023,
[   1.0000000]     2024
[   1.0000000]     The NetBSD Foundation, Inc.  All rights reserved.
[   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[   1.0000000]     The Regents of the University of California.  All rights
reserved.

[   1.0000000] NetBSD 9.4 (INSTALL32_IP3x) #0: Sat Apr 20 13:32:22 UTC 2024
[   1.0000000]
mkrepro%mkrepro.NetBSD.org@localhost:/usr/src/sys/arch/sgimips/compile/INSTALL32_IP3x
[   1.0000000] total memory = 255 MB
[   1.0000000] (6848 KB reserved for ARCS)
[   1.0000000] avail memory = 235 MB
[   1.0000000] mainbus0 (root): SGI-IP32 [SGI, 6], 1 processor
[   1.0000000] cpu0 at mainbus0: MIPS R12000 CPU (0xe35) Rev. 3.5 with
unknown FPC type (0x900) Rev. 0.0
[   1.0000000] cpu0: 64 TLB entries, 16MB max page size
[   1.0000000] cpu0: 32KB/64B 2-way set-associative L1 instruction cache
[   1.0000000] cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
[   1.0000000] cpu0: 2048KB/64B 2-way set-associative write-back L2 data
cache
[   1.0000000] crime0 at mainbus0 addr 0x14000000: rev 1.4 (CRIME_ID:
17592186044577)
[   1.0000000] crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics
Display Engine
[   1.0000000] crmfb0: device unusable if not setup by firmware
[   1.0000000] mace0 at mainbus0 addr 0x1f000000
[   1.0000000] lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
[   1.0000000] com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000:
ns16550a, working fifo
[   1.0000000] com0: console
[   1.0000000] com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000:
ns16550a, working fifo
[   1.0000000] macekbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0: PS2
controller
[   1.0000000] mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
[   1.0000000] mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110
Ethernet, rev 1
[   1.0000000] mec0: Ethernet address 08:00:69:0e:cd:96
[   1.0000000] nsphy0 at mec0 phy 8: DP83840 10/100 media interface, rev. 1
[   1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
[   1.0000000] mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: AD1843
rev 1
[   1.0000000] audio0 at mavb0: playback
[   1.0000000] audio0: slinear_be:16 -> slinear_be:24 2ch 48000Hz, blk 3840
bytes (10ms) for playback
[   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
[   1.0000000] wsbell at spkr0 not configured
[   1.0000000] macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
[   1.0000000] pci0 at macepci0 bus 0
[   1.0000000] ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI
adapter
[   1.0000000] ahc0: interrupting at crime interrupt 8
[   1.0000000] ahc0: Using left over BIOS settings
[   1.0000000] ahc0: Host Adapter has no SEEPROM. Using default SCSI target
parameters
[   1.0000000] ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
[   1.0000000] scsibus0 at ahc0: 16 targets, 8 luns per target
[   1.0000000] ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI
adapter
[   1.0000000] ahc1: interrupting at crime interrupt 9
[   1.0000000] ahc1: Using left over BIOS settings
[   1.0000000] ahc1: Host Adapter has no SEEPROM. Using default SCSI target
parameters
[   1.0000000] ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
[   1.0000000] scsibus1 at ahc1: 16 targets, 8 luns per target
[   1.0000030] scsibus0: waiting 2 seconds for devices to settle...
[   1.0710811] scsibus1: waiting 2 seconds for devices to settle...
[   3.3933196] sd0 at scsibus0 target 2 lun 0: <SGI, IBM  DCHS04Y, 3030>
disk fixed
[   3.6236201] sd0: 4340 MB, 6077 cyl, 9 head, 162 sec, 512 bytes/sect x
8888543 sectors
[   3.7142354] sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
tagged queueing
[   4.0847792] cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA,
3605> cdrom removable
[   4.1975116] cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
[  12.4612445] sd1 at scsibus1 target 2 lun 0: <AVID, ST3146707LW, AS01>
disk fixed
[  12.5515746] sd1: 136 GB, 90774 cyl, 4 head, 789 sec, 512 bytes/sect x
286749610 sectors
[  12.6493940] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
tagged queueing
[  12.7505645] sd2 at scsibus1 target 3 lun 0: <IBM, DCAS-34330, S65A> disk
fixed
[  12.9017837] sd2: 4134 MB, 8205 cyl, 6 head, 171 sec, 512 bytes/sect x
8467200 sectors
[  12.9963642] sd2: sync (50.00ns offset 15), 8-bit (20.000MB/s) transfers,
tagged queueing
[  16.2460696] WARNING: 1 error while detecting hardware; check system log.
[  16.3282530] boot device: sd2
[  16.4328125] root on md0a dumps on md0b
[  16.4785376] root file system type: ffs
[  16.5267143] kern.module.path=/stand/sgimips/9.4/modules
Created mfs /dev (282624 byte, 480 inodes)
-sh: tset: not found
erase ^?, werase ^W, kill ^U, intr ^C

Previously, I was able to boot netbsd-INSTALL32_IP3x of 10.0, but it hung up
during the installation. However, when I tried it recently, it just shut
down during the boot up and I couldn't boot it.
After this, it wouldn't turn on, but I've only just managed to revive it
using jumpstart, so I don't have any adding information.

2)R5000SC
On my O2 I could boot 9.0, 8.3 and 7.2 but not 9.1 or later.
When 9.1 or later failed to boot, my O2 froze during kernel boot and the LED
turned amber. At this point, pressing the reset button restarted it. (With
some exceptions noted in P.S.)
I suspect it is PR#57654.
I tried 9.1 by replacing the three changed files with the 9.0 ones, and it
booted up.

> hinv
                   System: IP32
                Processor: 200 Mhz R5000, with FPU
     Primary I-cache size: 32 Kbytes
     Primary D-cache size: 32 Kbytes
     Secondary cache size: 1024 Kbytes
              Memory size: 256 Mbytes
                 Graphics: CRM, Rev C
                    Audio: A3 version 1
                SCSI Disk: scsi(0)disk(1)
                SCSI Disk: scsi(0)disk(2)
               SCSI CDROM: scsi(0)cdrom(4)
> version


PROM Monitor (BE)
Tue Oct 22 10:58:00 PDT 2002 
VERSION 4.18
O2 R5K/R7K/R10K/R12K
IRIX 6.5.x IP32prom IP32PROM-v4

> boot -f scsi(0)cdrom(4)partition(8)ip3xboot
54464+1792 entry: 0x80002000

NetBSD/sgimips 9.1 Bootstrap, Revision 1.5 (Wed Oct 11 17:23:46 UTC 2023)

devopen: scsi(0)cdrom(4)partition(0) type scsi file ip3x
11845872+131824=0xb6c878
[   1.0000000] phys segment: 0xe000 @ 0x2000
[   1.0000000] adding 0xe000 @ 0x2000 to freelist 0
[   1.0000000] phys segment: 0xd40000 @ 0x10000
[   1.0000000] adding 0x56000 @ 0x10000 to freelist 0
[   1.0000000] adding 0x182000 @ 0xbce000 to freelist 0
[   1.0000000] phys segment: 0xec00000 @ 0x1400000
[   1.0000000] adding 0xec00000 @ 0x1400000 to freelist 0
[   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
2004, 2005,
[   1.0000000]     2006, 2007, 2008, 2009, 2010, 2011, 2012, 2013, 2014,
2015, 2016, 2017,
[   1.0000000]     2018, 2019, 2020 The NetBSD Foundation, Inc.  All rights
reserved.
[   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[   1.0000000]     The Regents of the University of California.  All rights
reserved.

[   1.0000000] NetBSD 9.1 (INSTALL32_IP3x) #0: Thu Oct 12 02:55:22 JST 2023
[   1.0000000]
iwama%netbsd-v.led.t3.rim.or.jp@localhost:/home/iwama/NetBSD-9.1-sgimips-indy/usr/obj/
sys/arch/sgimips/compile/INSTALL32_IP3x
[   1.0000000] total memory = 255 MB
[   1.0000000] (6848 KB reserved for ARCS)
[   1.0000000] avail memory = 235 MB
[   1.0000000] mainbus0 (root): SGI-IP32 [SGI, 0], 1 processor
[   1.0000000] cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with
built-in FPU Rev. 1.0
[   1.0000000] cpu0: 48 TLB entries, 16MB max page size
[   1.0000000] cpu0: 32KB/32B 2-way set-associative L1 instruction cache
[   1.0000000] cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
[   1.0000000] cpu0: 1024KB/32B direct-mapped write-through L2 unified cache
[   1.0000000] crime0 at mainbus0 addr 0x14000000: rev 1.1 (CRIME_ID: 161)
[   1.0000000] crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics
Display Engine
[   1.0000000] crmfb0: device unusable if not setup by firmware
[   1.0000000] mace0 at mainbus0 addr 0x1f000000
[   1.0000000] lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
[   1.0000000] com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000:
ns16550a, working fifo
[   1.0000000] com0: console
[   1.0000000] com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000:
ns16550a, working fifo
[   1.0000000] macekbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0: PS2
controller
[   1.0000000] mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
[   1.0000000] mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110
Ethernet, rev 1
[   1.0000000] mec0: Ethernet address 08:00:69:05:a4:60
[   1.0000000] nsphy0 at mec0 phy 31: DP83840 10/100 media interface, rev. 1
[   1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
100baseT4, auto
[   1.0000000] mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: AD1843
rev 1
[   1.0000000] audio0 at mavb0: playback
[   1.0000000] audio0: slinear_be:16 -> slinear_be:24 2ch 48000Hz, blk 3840
bytes (10ms) for playback
[   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
[   1.0000000] wsbell at spkr0 not configured
[   1.0000000] macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
[   1.0000000] pci0 at macepci0 bus 0
[   1.0000000] ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI
adapter
[   1.0000000] ahc0: interrupting at crime interrupt 8
[   1.0000000] ahc0: Using left over BIOS settings
[   1.0000000] ahc0: Host Adapter has no SEEPROM. Using default SCSI target
parameters
[   1.0000000] ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
[   1.0000000] scsibus0 at ahc0: 16 targets, 8 luns per target
[   1.0000000] ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI
adapter
[   1.0000000] ahc1: interrupting at crime interrupt 9
[   1.0000000] ahc1: Using left over BIOS settings
[   1.0000000] ahc1: Host Adapter has no SEEPROM. Using default SCSI target
parameters
[   1.0000000] ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
[   1.0000000] scsibus1 at ahc1: 16 targets, 8 luns per target
[   1.0000030] scsibus0: waiting 2 seconds for devices to settle...
[   1.0716207] scsibus1: waiting 2 seconds for devices to settle...
[   3.1338656] sd0 at scsibus0 target 1 lun 0: <FUJITSU, MAN3184MC, 0108>
disk fixed
[   3.2250875] sd0: 17366 MB, 30050 cyl, 2 head, 591 sec, 512 bytes/sect x
35566483 sectors
[   3.3233260] sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
tagged queueing
[   3.4230386] sd1 at scsibus0 target 2 lun 0: <MAXTOR, ATLAS10K5_73SCA,
JS03> disk fixed
[   3.5177076] sd1: 69809 MB, 81782 cyl, 2 head, 874 sec, 512 bytes/sect x
142969680 sectors
[   3.6180393] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
tagged queueing
[   3.9886950] cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA,
3605> cdrom removable
[   4.1015337] cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
[  16.0253745] WARNING: 1 error while detecting hardware; check system log.
[  16.1071668] boot device: <unknown>
[  16.1480027] root on md0a dumps on md0b
[  16.1898947] root file system type: ffs
[  16.2380823] kern.module.path=/stand/sgimips/9.1/modules
[  16.3009134] WARNING: clock lost 10145 days
[  16.3501358] WARNING: using filesystem time
[  16.3993676] WARNING: CHECK AND RESET THE DATE!
Created mfs /dev (282624 byte, 480 inodes)
-sh: tset: not found
erase ^?, werase ^W, kill ^U, intr ^C

The three files replaced:
sys/arch/mips/include/cache_r5k.h
sys/arch/mips/mips/cache_r5k.c
sys/arch/mips/mips/cache_r5k_subr.S

I was also able to get 10.0 to boot by replacing three files.

> boot -f scsi(0)disk(1)rdisk(0)partition(8)sash
scsi(0)disk(1)rdisk(0)partition(0)NetBSD/10.0-r5k/netbsd-INSTALL32_IP3x
136992+22896+3248+341792+49584d+4620+6880 entry: 0x8ffa5e50
12132496+130944 entry: 0x80069000
[   1.0000000] phys segment: 0x5e000 @ 0x2000
[   1.0000000] adding 0x5e000 @ 0x2000 to freelist 0
[   1.0000000] phys segment: 0xbb2000 @ 0x60000
[   1.0000000] adding 0x6000 @ 0x60000 to freelist 0
[   1.0000000] skipping 0xbac000 @ 0x66000 (kernel)
[   1.0000000] phys segment: 0x13c000 @ 0xc14000
[   1.0000000] adding 0x13c000 @ 0xc14000 to freelist 0
[   1.0000000] phys segment: 0xeb84000 @ 0x1400000
[   1.0000000] adding 0xeb84000 @ 0x1400000 to freelist 0
[   1.0000000] phys segment: 0x7c000 @ 0xff84000
[   1.0000000] adding 0x7c000 @ 0xff84000 to freelist 0
[   1.0000000] Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003,
[   1.0000000]     2004, 2005, 2006, 2007, 2008, 2009, 2010, 2011, 2012,
2013,
[   1.0000000]     2014, 2015, 2016, 2017, 2018, 2019, 2020, 2021, 2022,
2023,
[   1.0000000]     2024
[   1.0000000]     The NetBSD Foundation, Inc.  All rights reserved.
[   1.0000000] Copyright (c) 1982, 1986, 1989, 1991, 1993
[   1.0000000]     The Regents of the University of California.  All rights
reserved.

[   1.0000000] NetBSD 10.0 (INSTALL32_IP3x) #0: Wed Jul  3 12:20:58 JST 2024
[   1.0000000]
iwama%netbsd-v.led.t3.rim.or.jp@localhost:/home/iwama/NetBSD-10.0-sgimips-r5k/usr/obj/
sys/arch/sgimips/compile/INSTALL32_IP3x
[   1.0000000] total memory = 255 MB
[   1.0000000] (6848 KB reserved for ARCS)
[   1.0000000] avail memory = 234 MB
[   1.0000000] mainbus0 (root): SGI-IP32 [SGI, 0], 1 processor
[   1.0000000] cpu0 at mainbus0: MIPS R5000 CPU (0x2321) Rev. 2.1 with
built-in FPU Rev. 1.0
[   1.0000000] cpu0: 48 TLB entries, 16MB max page size
[   1.0000000] cpu0: 32KB/32B 2-way set-associative L1 instruction cache
[   1.0000000] cpu0: 32KB/32B 2-way set-associative write-back L1 data cache
[   1.0000000] cpu0: 1024KB/32B direct-mapped write-through L2 unified cache
[   1.0000000] crime0 at mainbus0 addr 0x14000000: rev 1.1 (CRIME_ID: 161)
[   1.0000000] crmfb0 at mainbus0 addr 0x16000000: SGI CRIME Graphics
Display Engine
[   1.0000000] crmfb0: device unusable if not setup by firmware
[   1.0000000] mace0 at mainbus0 addr 0x1f000000
[   1.0000000] lpt0 at mace0 offset 0x380000 intr 4 intrmask 0xf0000
[   1.0000000] com0 at mace0 offset 0x390000 intr 4 intrmask 0x3f00000:
ns16550a, 16-byte FIFO
[   1.0000000] com0: console
[   1.0000000] com1 at mace0 offset 0x398000 intr 4 intrmask 0xfc000000:
ns16550a, 16-byte FIFO
[   1.0000000] macekbc0 at mace0 offset 0x320000 intr 5 intrmask 0x0: PS2
controller
[   1.0000000] mcclock0 at mace0 offset 0x3a0000 intrmask 0x0
[   1.0000000] mec0 at mace0 offset 0x280000 intr 3 intrmask 0x0: MAC-110
Ethernet, rev 1
[   1.0000000] mec0: Ethernet address 08:00:69:05:a4:60
[   1.0000000] nsphy0 at mec0 phy 31: DP83840 10/100 media interface, rev. 1
[   1.0000000] nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX,
100baseT4, auto
[   1.0000000] mavb0 at mace0 offset 0x300000 intr 6 intrmask 0x0: AD1843
rev 1
[   1.0000000] audio0 at mavb0: playback
[   1.0000000] audio0: slinear_be:16 -> slinear_be:24 2ch 48000Hz, blk 3840
bytes (10ms) for playback
[   1.0000000] spkr0 at audio0: PC Speaker (synthesized)
[   1.0000000] wsbell at spkr0 not configured
[   1.0000000] macepci0 at mace0 offset 0x80000 intr 7 intrmask 0x0: rev 1
[   1.0000000] pci0 at macepci0 bus 0
[   1.0000000] ahc0 at pci0 dev 1 function 0: Adaptec aic7880 Ultra SCSI
adapter
[   1.0000000] ahc0: interrupting at crime interrupt 8
[   1.0000000] ahc0: Using left over BIOS settings
[   1.0000000] ahc0: Host Adapter has no SEEPROM. Using default SCSI target
parameters
[   1.0000000] ahc0: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
[   1.0000000] scsibus0 at ahc0: 16 targets, 8 luns per target
[   1.0000000] ahc1 at pci0 dev 2 function 0: Adaptec aic7880 Ultra SCSI
adapter
[   1.0000000] ahc1: interrupting at crime interrupt 9
[   1.0000000] ahc1: Using left over BIOS settings
[   1.0000000] ahc1: Host Adapter has no SEEPROM. Using default SCSI target
parameters
[   1.0000000] ahc1: aic7880: Ultra Wide Channel A, SCSI Id=0, 16/253 SCBs
[   1.0000000] scsibus1 at ahc1: 16 targets, 8 luns per target
[   1.0000030] scsibus0: waiting 2 seconds for devices to settle...
[   1.0720794] scsibus1: waiting 2 seconds for devices to settle...
[   1.1443046] WARNING: system needs entropy for security; see entropy(7)
[   3.2063158] sd0 at scsibus0 target 1 lun 0: <FUJITSU, MAN3184MC, 0108>
disk fixed
[   3.2997954] sd0: 17366 MB, 30050 cyl, 2 head, 591 sec, 512 bytes/sect x
35566483 sectors
[   3.3979275] sd0: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
tagged queueing
[   3.4974353] sd1 at scsibus0 target 2 lun 0: <MAXTOR, ATLAS10K5_73SCA,
JS03> disk fixed
[   3.5959757] sd1: 69809 MB, 81782 cyl, 2 head, 874 sec, 512 bytes/sect x
142969680 sectors
[   3.6952592] sd1: sync (50.00ns offset 8), 16-bit (40.000MB/s) transfers,
tagged queueing
[   4.3447666] cd0 at scsibus0 target 4 lun 0: <TOSHIBA, CD-ROM XM-5401TA,
3605> cdrom removable
[   4.4547315] cd0: sync (236.00ns offset 15), 8-bit (4.237MB/s) transfers
[  18.2085692] WARNING: 1 error while detecting hardware; check system log.
[  18.2960639] boot device: sd0
[  18.3406213] root on md0a dumps on md0b
[  18.3877962] root file system type: ffs
[  18.4359858] kern.module.path=/stand/sgimips/10.0/modules
Created mfs /dev (282624 byte, 480 inodes)
[  19.0399028] entropy: best effort
-sh: tset: not found
erase ^?, werase ^W, kill ^U, intr ^C

Regards,
-- 
Yoshihiko Iwama

P.S.
With some kernels, the power would suddenly shut off during boot, and after
that, the power would not turn on even when I pressed the power switch.
I tried
jumpstart(https://wiki.preterhuman.net/O2_Diagnostics:_The_Jumpstart_Procedu
re) and both were able to boot again.
Follow-Ups:
- RE: SGI O2 unable to boot 9.0+ (status update)
  - From: iwama
References:
- re: SGI O2 unable to boot 9.0+ (status update)
  - From: matthew green
- re: SGI O2 unable to boot 9.0+ (status update)
  - From: matthew green
Prev by Date: Re: PCCONS still needed for Xorg
Next by Date: Re: SGI O2 unable to boot 9.0+ (status update)
Previous by Thread: re: SGI O2 unable to boot 9.0+ (status update)
Next by Thread: RE: SGI O2 unable to boot 9.0+ (status update)
Indexes:
Home | Main Index | Thread Index | Old Index