Re: Synology CS 407e: altboot fails to load installer.

[Oscar Molin <oscarmolin%gmail.com@localhost>]

here is the full output:


_MPC824X > go 1000000 debug
## Starting application at 0x01000000 ...

>> NetBSD/sandpoint altboot, revision 1.7 (Tue Apr 19 09:38:13 CEST 2011)
>> Synology DS, cpu 265 MHz, bus 132 MHz, 64MB SDRAM
1095.3512 DSK 00:12:00
1095.3512 DSK 00:13:00
11ab.4320 NET 00:15:00
1033.0035 USB 00:14:00
1033.0035 USB 00:14:00
1033.0035 USB 00:14:00
00:00:00: chip 1057.0006 card ffff.ffff rev 14 class 06.00.00 hdr 00
mem base 80000000 size 1000
00:12:00: chip 1095.3512 card 1095.3512 rev 01 class 01.80.00 hdr 00
i/o base 1000 size 10
i/o base 1010 size 10
i/o base 1020 size 10
i/o base 1030 size 10
i/o base 1040 size 10
mem base 80001000 size 1000
00:13:00: chip 1095.3512 card 1095.3512 rev 01 class 01.80.00 hdr 00
i/o base 1050 size 10
i/o base 1060 size 10
i/o base 1070 size 10
i/o base 1080 size 10
i/o base 1090 size 10
mem base 80002000 size 1000
00:14:00: chip 1033.0035 card 1033.0035 rev 43 class 0c.03.10 hdr 80
mem base 80003000 size 1000
00:14:01: chip 1033.0035 card 1033.0035 rev 43 class 0c.03.10 hdr 00
mem base 80004000 size 1000
00:14:02: chip 1033.00e0 card 1033.00e0 rev 04 class 0c.03.20 hdr 00
mem base 80005000 size 1000
00:15:00: chip 11ab.4320 card 11ab.0121 rev 13 class 02.00.00 hdr 00
mem base 80008000 size 4000
i/o base 1100 size 100
MAC address 00:11:xx:xx:xx:xx
PHY 0 (0141.0c25)
100Mbps-FDX
Hit any key to enter interactive mode: 2
bootargs> tftp:

xmit failed
xmit failed
xmit failed
xmit failed
bootp: no reply
"" not found
load failed. Restarting...





2011/5/8 Oscar Molin <oscarmolin%gmail.com@localhost>:
> Thank you for your quick reply.
>
> I can confirm there is a 88E8001 chip on board.
>
> here is some of the output in debug mode:
>
> MAC address xx:xx....  (correct address)
> PHY 0 (0141.0c25)
> 100Mbps-FDX
>
> xmit failed .....
>
> I had the full output but this was the ones you asked for.
> I can't copy paste from my terminal program.
>
> This xmit failed message I assume is a message from net driver,
> hopefully from the sk98 driver or whatever you have in altboot for sk.
> I guess the "xmit failed" is a failed transmission, possibly of the
> first dhcp request message?
>
> If you have any ideas I'll be willing to try it, tough I won't be able
> to compile anything myself because I don't run netbsd myself and
> setting up a build environment for a noob like me will take all day.
>
> As a note for anyone else trying this hardware, the serial header for
> the cubestation 407e is located near the SATA ports and labeled JP2,
> pinout is the same as in the sandpoint synology install guide
>
> /Oscar
>
> 2011/5/8 Frank Wille <frank%phoenix.owl.de@localhost>:
>> On Sun, 8 May 2011 12:00:31 +0200
>> Oscar Molin <oscarmolin%gmail.com@localhost> wrote:
>>
>>> I'm trying to install netbsd, latest binary snapshot 201105062100Z on
>>> a Synology Cubestation 407e.
>>
>> Great! Reports from untested hardware are always welcome!
>>
>>
>>> Altboot loads, but never requests any IP from my server, doesnt seem
>>> to use ethernet at all, then gives the messages:
>>>
>>> xmit failed
>>> xmit failed
>>> xmit failed
>>> xmit failed
>>> bootp: no reply
>>
>> Can you show us the full output from altboot? There should be two lines
>> like...
>>
>> MAC address 00:11:32:xx:xx:xx
>> 100Mbps-FDX
>>
>> ...when the network interface was initialized and the link speed
>> negotiation was done.
>>
>> And can you confirm the type of the network chip? Is it Marvell SKnet as
>> on the other Synology NAS systems? There should be a 88E8001 chip on the
>> board.
>>
>> --
>> Frank Wille
>>
>