Hi,
	I have an SS20 running 1.5.2. I've built some 
kernel's because I want it to run both CPU's. But the
machine freezes during boot when the MP lines are added
to the config. I have to power down the machine, I can't
seem to send a break.

	I'm running headless using TeraTerm on my PC
to connect into it. I've tried my own kernel which works
fine without the MP lines and GENERIC.MP. Here's the
console:

SPARCstation 20 MP (2 X 625), No Keyboard
ROM Rev. 2.15, 128 MB memory installed, Serial #3525921.
Ethernet address 8:0:20:21:5f:22, Host ID: 7235cd21.



Rebooting with command:
Boot device: /iommu/sbus/espdma@f,400000/esp@f,800000/sd@1,0  File and
args:
>> NetBSD/sparc Secondary Boot, Revision 1.9
>> (toor@proxima, Tue Aug 21 23:18:13 CST 2001)
Booting netbsd
1792340+96716+182692 [68+119952+89171]=0x23cfb4
OBP version 3, revision 2.15 (plugin rev 2)
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 1.5.2 (SS20 MP) #3: Wed Feb 13 11:49:39 CST 2002
    root@ss20:/usr/src/sys/arch/sparc/compile/SS20
total memory = 127 MB
avail memory = 115 MB
using 896 buffers containing 6628 KB of memory
bootpath:
/iommu@f,e0000000/sbus@f,e0001000/espdma@f,400000/esp@f,800000/sd@1,0
mainbus0 (root): SUNW,SPARCstation-20
cpu0 at mainbus0: mid 8: RT620/625 @ 50 MHz, on-chip FPU
cpu0: 256K byte write-back, 64 bytes/line, sw flush: cache enabled
cpu1 at mainbus0: mid 10: RT620/625 @ 50 MHz, on-chip FPU
cpu1: 256K byte write-back, 64 bytes/line, sw flush: cache enabled
obio0 at mainbus0
clock0 at obio0 slot 0 offset 0x200000: mk48t08 (eeprom)
timer0 at obio0 slot 0 offset 0x300000 delay constant 48
zs0 at obio0 slot 0 offset 0x100000 level 12 softpri 6
zstty0 at zs0 channel 0 (console i/o)
zstty1 at zs0 channel 1
zs1 at obio0 slot 0 offset 0x0 level 12 softpri 6
kbd0 at zs1 channel 0
ms0 at zs1 channel 1
fdc0 at obio0 slot 0 offset 0x700000 level 11: no drives attached
auxreg0 at obio0 slot 0 offset 0x800000
power0 at obio0 slot 0 offset 0xa01000 level 2
iommu0 at mainbus0 ioaddr 0xe0000000: version 0x1/0x1, page-size 4096,
range 64M
B
sbus0 at iommu0: clock = 25 MHz
dma0 at sbus0 slot 15 offset 0x400000: rev 2
esp0 at dma0 slot 15 offset 0x800000 level 4: ESP200, 40MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
ledma0 at sbus0 slot 15 offset 0x400010: rev 2
le0 at ledma0 slot 15 offset 0xc00000 level 6: address 08:00:20:21:5f:22
le0: 8 receive buffers, 2 transmit buffers
bpp0 at sbus0 slot 15 offset 0x4800000 level 2 (ipl 3): rev 2
SUNW,DBRIe at sbus0 slot 14 offset 0x10000 level 9 not configured
cgsix0 at sbus0 slot 2 offset 0x0 level 9: SUNW,501-2325, 1152 x 900,
rev 11
cgsix0: attached to /dev/fb
eccmemctl0 at mainbus0: version 0x0/0x2
scsibus0: waiting 2 seconds for devices to settle...
probe(esp0:1:0): max sync rate 10.00MB/s
sd0 at scsibus0 target 1 lun 0: <SEAGATE, ST32430W SUN2.1G, 0666> SCSI2
0/direct
 fixed
sd0: 2049 MB, 3992 cyl, 9 head, 116 sec, 512 bytes/sect x 4197405
sectors
probe(esp0:3:0): max sync rate 10.00MB/s
sd1 at scsibus0 target 3 lun 0: <SEAGATE, ST31200W SUN1.05, 8566> SCSI2
0/direct
 fixed
sd1: 1006 MB, 2700 cyl, 9 head, 84 sec, 512 bytes/sect x 2061108 sectors
probe(esp0:6:0): max sync rate 4.23MB/s
cd0 at scsibus0 target 6 lun 0: <TOSHIBA, XM-4101TASUNSLCD, 1755> SCSI2
5/cdrom
removable
root on sd0a dumps on sd0b


Any help?

-- 
Paul T. Root                    E/Mail: proot@iaces.com
600 Stinson Blvd, Fl 1S		PAG: +1 (877) 693-7155
Minneapolis, MN  55413          WRK: +1 (612) 664-3385
NIC:    PTR                     FAX: +1 (612) 664-4779