I had a problem with my old HD in my sparcbook and it no longer boots.
I figured this was as good a time as any to install NetBSD on it, so
I went and grabbed the latest stuff Michael posted to his area on
ftp.netbsd.org and got it to install.

Here's where things get a little goofy, I can boot it up fine, log in
once, but when I log out and back in, I get:

"getty respawning too quickly on /dev/console, sleeping"

It sleeps for a bit, then it gives me another login prompt.  It will do
this a couple of times, then it starts just giving me login prompts,
never prompting for password.

Below is the uname -a and dmesg output.

Ideas?

(btw, this does feel much faster than Solaris 2.6 did)

-- 
Michael Parson
mparson@bl.org

NetBSD tadpole 3.99.7 NetBSD 3.99.7 (MORGOTH) #60: Fri Jul 15 18:24:13 EDT 2005  ml@Inishowen:/stuff/build/obj_sparc/sys/arch/sparc/compile/MORGOTH sparc

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 3.99.7 (MORGOTH) #60: Fri Jul 15 18:24:13 EDT 2005
	ml@Inishowen:/stuff/build/obj_sparc/sys/arch/sparc/compile/MORGOTH
total memory = 65200 KB
avail memory = 61120 KB
bootpath: /iommu@0,10000000/sbus@0,10001000/espdma@4,8400000/esp@4,8800000/sd@3,0
mainbus0 (root): Tadpole_S3GX: hostid 80ae2037
cpu0 at mainbus0: MB86904 @ 110 MHz, on-chip FPU
cpu0: 16K instruction (32 b/l), 8K data (16 b/l): cache enabled
obio0 at mainbus0
clock0 at obio0 slot 0 offset 0x202000: mk48t08
timer0 at obio0 slot 0 offset 0xd00000: delay constant 52
zs0 at obio0 slot 0 offset 0x100000 level 12 powered via auxio2 softpri 6
zstty0 at zs0 channel 0
zstty1 at zs0 channel 1
zs1 at obio0 slot 0 offset 0x0 level 12 softpri 6
zstty2 at zs1 channel 0 (console input)
kbd0 at zstty2 (console input)
zstty3 at zs1 channel 1
ms0 at zstty3
wsmouse0 at ms0 mux 0
slavioconfig at obio0 slot 0 offset 0x800000 not configured
auxreg0 at obio0 slot 0 offset 0x900000
auxiotwo0 at obio0 slot 0 offset 0x910000
tctrl0 at obio0 slot 0 offset 0xd1000020 level 11
tctrl0: main power available, lid down
clkctrl0 at obio0 slot 0 offset 0x3c0000
com0 at obio0 slot 0 offset 0x3a0000 level 13: ns16550a, working fifo
iommu0 at mainbus0 addr 0x10000000: version 0x4/0x0, page-size 4096, range 64MB
sbus0 at iommu0: clock = 22 MHz
pnozz0 at sbus0 slot 0 offset 0x8000000 level 2: rev 4, 800x600, depth 8 mem 200000 (console)
wsdisplay0 at pnozz0 kbdmux 1: console (default, vt100 emulation)
wsmux1: connecting to wsdisplay0
pnozz0: attached to /dev/fb0
dma0 at sbus0 slot 4 offset 0x8400000: DMA rev 2
esp0 at dma0 slot 4 offset 0x8800000 level 4: ESP200, 40MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
SUNW,bpp at sbus0 slot 4 offset 0xc800000 level 3 not configured
ledma0 at sbus0 slot 4 offset 0x8400010: DMA rev 2
le0 at ledma0 slot 4 offset 0x8c00000 level 6: address 00:00:83:ae:20:37
le0: 8 receive buffers, 2 transmit buffers
tslot0 at sbus0 slot 1 offset 0x2000000 level 11: 2 slots
pcmcia0 at tslot0 socket 0
pcmcia1 at tslot0 socket 1
dbri0 at sbus0 slot 2 offset 0x40 level 9
dbri0: need to power up first....done
wskbd0 at kbd0: console keyboard, using wsdisplay0
dbri0: onboard CS4215 detected
dbri0: cs4215 ver 2 found at offset 0
audio0 at dbri0: half duplex, mmap
scsibus0: waiting 2 seconds for devices to settle...
sd0 at scsibus0 target 3 lun 0: <HITACHI_, DK23AA-12B, 1.06> disk fixed
sd0: 11509 MB, 24944 cyl, 15 head, 63 sec, 512 bytes/sect x 23572080 sectors
sd0: sync (100.00ns offset 15), 8-bit (10.000MB/s) transfers
root on sd0a dumps on sd0b
root file system type: ffs