Hi!

I have an old Sun Utra5 running 1.5X and I'd like to have X11 working.
Running xinit won't work:

- X is symlink to Xsun (I've tried also Xsun24 and XsunMono)
- I don't have normal Sun integrated display adapter but a
  standard PCI graphics card (although it's marked as "not configured")

Are these correct assuptions based on the following dmesg? And this means
I have to compile XFree (3 or 4?) from xsrx and run XF86Setup?

All I get from startx is with the current setup:

    # startx
    Fatal server error:
    no screens found
    X connection to :0.0 broken (explicit kill or server shutdown)

And here's the dmesg:

    NetBSD 1.5X (GENERIC) #1: Wed Aug 22 22:58:29 EST 2001
    mrg@powerofseven.eterna.com.au:/orb/a/obj.sparc64/usr/src/sys/arch/sparc64/c
ompile/GENERIC
    total memory = 192 MB
    avail memory = 164 MB
    using 1241 buffers containing 9928 KB of memory
    bootpath: /pci@1f,0/pci@1,1/ide@3,0/disk@0,0
    mainbus0 (root): SUNW,Ultra-5_10
    cpu0 at mainbus0: SUNW,UltraSPARC-IIi @ 269.807 MHz, version 0 FPU
    cpu0: physical 4K instruction (32 b/l), 4K data (32 b/l), 2048K external (64
 b/l)
    psycho0 at mainbus0 addr 0xfffc4000
    SUNW,sabre: impl 0, version 0: ign 7c0 bus range 0 to 2; PCI bus 0
    intr_establish: intr reused 7c0
    DVMA map: c0000000 to e0000000
    pci0 at psycho0
    pci0: i/o space, memory space enabled
    ppb0 at pci0 dev 1 function 1: Sun Microsystems Simba PCI bridge (rev. 0x11)
    pci1 at ppb0 bus 1
    pci1: i/o space, memory space enabled
    ebus0 at pci1 dev 1 function 0
    ebus0: Sun Microsystems PCIO Ebus2, revision 0x01
    auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 72c000-72c
003, 72f000-72f003
    power at ebus0 addr 724000-724003 ipl 37 not configured
    SUNW,pll at ebus0 addr 504000-504002 not configured
    se at ebus0 addr 400000-40007f ipl 43 not configured
    com0 at ebus0 addr 3083f8-3083ff ipl 41: ns16550a, working fifo
    com0: console
    kbd0 at com0 (console input)
    com1 at ebus0 addr 3062f8-3062ff ipl 42: ns16550a, working fifo
    ms0 at com1
    lpt0 at ebus0 addr 3043bc-3043cb, 30015c-30015d, 700000-70000f ipl 34
    fdthree at ebus0 addr 3023f0-3023f7, 706000-70600f, 720000-720003 ipl 39 not
 configured
    clock0 at ebus0 addr 0-1fff: mk48t59: hostid 8090c146
    flashprom at ebus0 addr 0-fffff not configured
    SUNW,CS4231 at ebus0 addr 200000-2000ff, 702000-70200f, 704000-70400f, 72200
0-72
    2003 ipl 35 ipl 36 not configured
    hme0 at pci1 dev 1 function 1: address 08:00:20:90:c1:46
    nsphy0 at hme0 phy 1: DP83840 10/100 media interface, rev. 1
    nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
    OF_mapintr failed
    hme0: using ivec 3021 for interrupt
    pciide0 at pci1 dev 3 function 0: CMD Technology PCI0646 (rev. 0x03)
    pciide0: bus-master DMA support present
    pciide0: primary channel configured to native-PCI mode
    OF_mapintr failed
    pciide0: using ivec 1820 for native-PCI interrupt
    wd0 at pciide0 channel 0 drive 0: <ST34342A>
    wd0: drive supports 16-sector PIO transfers, LBA addressing
    wd0: 4103 MB, 8894 cyl, 15 head, 63 sec, 512 bytes/sect x 8404830 sectors
    wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
    wd0(pciide0:0:0): using PIO mode 4, DMA mode 2 (using DMA data transfers)
    pciide0: secondary channel configured to native-PCI mode
    pciide0: disabling secondary channel (no drives)
    ppb1 at pci0 dev 1 function 0: Sun Microsystems Simba PCI bridge (rev. 0x11)
    pci2 at ppb1 bus 2
    pci2: i/o space, memory space enabled
    Number 9 Computer Company Imagine-128 II (VGA display, revision 0x02) at pci
2 dev 1 function 0 not configured
    pcons at mainbus0 not configured
    No counter-timer -- using %tick at 269MHz as system clock.
    Using %tick -- intr in 2698073 cycles...done.

Martti

---
Martti Kuparinen <martti.kuparinen@iki.fi>              NetBSD - No media hype
http://www.iki.fi/~kuparine/                            http://www.netbsd.org/