here some more information about the maschine configuration:


NetBSD 3.0 (DEBUG) #1: Fri Jan  6 12:24:40 CET 2006
        root@ultron:/usr/src/sys/arch/sparc64/compile/DEBUG
total memory = 256 MB
avail memory = 237 MB
bootpath: /pci@1f,4000/scsi@3,0/disk@0,0
mainbus0 (root): SUNW,Ultra-80: hostid 80f027cf
cpu0 at mainbus0: SUNW,UltraSPARC-II @ 450.036 MHz, version 0 FPU
cpu0: 32K instruction (32 b/l), 16K data (32 b/l), 4096K external (64 b/l)
psycho0 at mainbus0 addr 0xfffb4000
SUNW,psycho: impl 0, version 4: ign 7c0 bus range 0 to 0; PCI bus 0
extent `psycho mem' (0x0 - 0x7fffffff), flags = 0x0
     0x0 - 0xfff
extent `psycho io' (0x0 - 0xffff), flags = 0x0
     0x0 - 0x3ff
decreasing interrupt retry timeout from fffff to 0xff
DVMA map: fe000000 to ffffe000
IOTSB: 42e000 to 436000
pci0 at psycho0
pci0: i/o space, memory space enabled
PCI configuration registers:
  Common header:
    0x00: 0x8000108e 0x02800046 0x06000000 0x00004000

    Vendor Name: Sun Microsystems (0x108e)
    Device Name: psycho PCI controller (0x8000)
    Command register: 0x0046
      I/O space accesses: off
      Memory space accesses: on
      Bus mastering: on
      Special cycles: off
      MWI transactions: off
      Palette snooping: off
      Parity error checking: on
      Address/data stepping: off
      System error (SERR): off
      Fast back-to-back transactions: off
    Status register: 0x0280
      Capability List support: off
      66 MHz capable: off
      User Definable Features (UDF) support: off
      Fast back-to-back capable: on
      Data parity error detected: off
      DEVSEL timing: medium (0x1)
      Slave signaled Target Abort: off
      Master received Target Abort: off
      Master received Master Abort: off
      Asserted System Error (SERR): off
      Parity error detected: off
    Class Name: bridge (0x06)
    Subclass Name: host (0x00)
    Interface: 0x00
    Revision ID: 0x00
    BIST: 0x00
    Header Type: 0x00 (0x00)
    Latency Timer: 0x40
    Cache Line Size: 0x00

  Type 0 ("normal" device) header:
    0x10: 0x00000000 0x00000000 0x00000000 0x00000000
    0x20: 0x00000000 0x00000000 0x00000000 0x00000000
    0x30: 0x00000000 0x00000000 0x00000000 0x00000000

    Base address register at 0x10
      not implemented(?)
    Base address register at 0x14
      not implemented(?)
    Base address register at 0x18
      not implemented(?)
    Base address register at 0x1c
      not implemented(?)
    Base address register at 0x20
      not implemented(?)
    Base address register at 0x24
      not implemented(?)
    Cardbus CIS Pointer: 0x00000000
    Subsystem vendor ID: 0x0000
    Subsystem ID: 0x0000
    Expansion ROM Base Address: 0x00000000
    Reserved @ 0x34: 0x00000000
    Reserved @ 0x38: 0x00000000
    Maximum Latency: 0x00
    Minimum Grant: 0x00
    Interrupt pin: 0x00 (none)
    Interrupt line: 0x00

  Device-dependent header:
    0x40: 0x00007f00 0x00000000 0x00000000 0x00000000
    0x50: 0x00000000 0x00000000 0x00000000 0x00000000
    0x60: 0x00000000 0x00000000 0x00000000 0x00000000
    0x70: 0x00000000 0x00000000 0x00000000 0x00000000
    0x80: 0x8000108e 0x02800046 0x06000000 0x00004000
    0x90: 0x00000000 0x00000000 0x00000000 0x00000000
    0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xc0: 0x00007f00 0x00000000 0x00000000 0x00000000
    0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xf0: 0x00000000 0x00000000 0x00000000 0x00000000

    Don't know how to pretty-print device-dependent header.

ebus0 at pci0 dev 1 function 0: PCI configuration registers:
  Common header:
    0x00: 0x1000108e 0x02800046 0x06800001 0x00805240

    Vendor Name: Sun Microsystems (0x108e)
    Device Name: PCIO Ebus2 (0x1000)
    Command register: 0x0046
      I/O space accesses: off
      Memory space accesses: on
      Bus mastering: on
      Special cycles: off
      MWI transactions: off
      Palette snooping: off
      Parity error checking: on
      Address/data stepping: off
      System error (SERR): off
      Fast back-to-back transactions: off
    Status register: 0x0280
      Capability List support: off
      66 MHz capable: off
      User Definable Features (UDF) support: off
      Fast back-to-back capable: on
      Data parity error detected: off
      DEVSEL timing: medium (0x1)
      Slave signaled Target Abort: off
      Master received Target Abort: off
      Master received Master Abort: off
      Asserted System Error (SERR): off
      Parity error detected: off
    Class Name: bridge (0x06)
    Subclass Name: miscellaneous (0x80)
    Interface: 0x00
    Revision ID: 0x01
    BIST: 0x00
    Header Type: 0x00+multifunction (0x80)
    Latency Timer: 0x52
    Cache Line Size: 0x40

  Type 0 ("normal" device) header:
    0x10: 0x70000000 0x71000000 0x00000000 0x00000000
    0x20: 0x00000000 0x00000000 0x00000000 0x00000000
    0x30: 0x01000000 0x00000000 0x00000000 0x190a0000

    Base address register at 0x10
      type: 32-bit nonprefetchable memory
      base: 0x70000000, size: 0x01000000
    Base address register at 0x14
      type: 32-bit nonprefetchable memory
      base: 0x71000000, size: 0x00800000
    Base address register at 0x18
      not implemented(?)
    Base address register at 0x1c
      not implemented(?)
    Base address register at 0x20
      not implemented(?)
    Base address register at 0x24
      not implemented(?)
    Cardbus CIS Pointer: 0x00000000
    Subsystem vendor ID: 0x0000
    Subsystem ID: 0x0000
    Expansion ROM Base Address: 0x01000000
    Reserved @ 0x34: 0x00000000
    Reserved @ 0x38: 0x00000000
    Maximum Latency: 0x19
    Minimum Grant: 0x0a
    Interrupt pin: 0x00 (none)
    Interrupt line: 0x00

  Device-dependent header:
    0x40: 0x00000000 0x00000000 0x00000000 0x00000000
    0x50: 0x00000000 0x00000000 0x00000000 0x00000000
    0x60: 0x00000000 0x00000000 0x00000000 0x00000000
    0x70: 0x00000000 0x00000000 0x00000000 0x00000000
    0x80: 0x00000000 0x00000000 0x00000000 0x00000000
    0x90: 0x00000000 0x00000000 0x00000000 0x00000000
    0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xf0: 0x00000000 0x00000000 0x00000000 0x00000000

    Don't know how to pretty-print device-dependent header.

Sun Microsystems PCIO Ebus2 (miscellaneous bridge, revision 0x01) at ? 
dev 1 function 0 (intrswiz 0, )
ebus0: Sun Microsystems PCIO Ebus2, revision 0x01
auxio0 at ebus0 addr 726000-726003, 728000-728003, 72a000-72a003, 
72c000-72c003, 72f000-72f003
power at ebus0 addr 724000-724003 ipl 37 not configured
SUNW,pll at ebus0 addr 504000-504002 not configured
sc at ebus0 addr 500000-500007 not configured
sab0 at ebus0 addr 400000-40007f ipl 43: rev 3.2
sabtty0 at sab0 port 0: console i/o
sabtty1 at sab0 port 1
com0 at ebus0 addr 3083f8-3083ff ipl 41: ns16550a, working fifo
kbd0 at com0
com1 at ebus0 addr 3062f8-3062ff ipl 42: ns16550a, working fifo
ms0 at com1
wsmouse0 at ms0 mux 0
lpt0 at ebus0 addr 3043bc-3043cb, 300398-300399, 700000-70000f ipl 34
fdthree at ebus0 addr 3023f0-3023f7, 706000-70600f, 720000-720003 ipl 39 
not configured
clock0 at ebus0 addr 0-1fff: mk48t59
flashprom at ebus0 addr 0-fffff not configured
hme0 at pci0 dev 1 function 1: PCI configuration registers:
  Common header:
    0x00: 0x1001108e 0x02800046 0x02000001 0x00805240

    Vendor Name: Sun Microsystems (0x108e)
    Device Name: PCIO Happy Meal Ethernet (0x1001)
    Command register: 0x0046
      I/O space accesses: off
      Memory space accesses: on
      Bus mastering: on
      Special cycles: off
      MWI transactions: off
      Palette snooping: off
      Parity error checking: on
      Address/data stepping: off
      System error (SERR): off
      Fast back-to-back transactions: off
    Status register: 0x0280
      Capability List support: off
      66 MHz capable: off
      User Definable Features (UDF) support: off
      Fast back-to-back capable: on
      Data parity error detected: off
      DEVSEL timing: medium (0x1)
      Slave signaled Target Abort: off
      Master received Target Abort: off
      Master received Master Abort: off
      Asserted System Error (SERR): off
      Parity error detected: off
    Class Name: network (0x02)
    Subclass Name: ethernet (0x00)
    Interface: 0x00
    Revision ID: 0x01
    BIST: 0x00
    Header Type: 0x00+multifunction (0x80)
    Latency Timer: 0x52
    Cache Line Size: 0x40

  Type 0 ("normal" device) header:
    0x10: 0x00008000 0x00000000 0x00000000 0x00000000
    0x20: 0x00000000 0x00000000 0x00000000 0x00000000
    0x30: 0x01000000 0x00000000 0x00000000 0x050a0000

    Base address register at 0x10
      type: 32-bit nonprefetchable memory
      base: 0x00008000, size: 0x00008000
    Base address register at 0x14
      not implemented(?)
    Base address register at 0x18
      not implemented(?)
    Base address register at 0x1c
      not implemented(?)
    Base address register at 0x20
      not implemented(?)
    Base address register at 0x24
      not implemented(?)
    Cardbus CIS Pointer: 0x00000000
    Subsystem vendor ID: 0x0000
    Subsystem ID: 0x0000
    Expansion ROM Base Address: 0x01000000
    Reserved @ 0x34: 0x00000000
    Reserved @ 0x38: 0x00000000
    Maximum Latency: 0x05
    Minimum Grant: 0x0a
    Interrupt pin: 0x00 (none)
    Interrupt line: 0x00

  Device-dependent header:
    0x40: 0x00000000 0x00000000 0x00000000 0x00000000
    0x50: 0x00000000 0x00000000 0x00000000 0x00000000
    0x60: 0x00000000 0x00000000 0x00000000 0x00000000
    0x70: 0x00000000 0x00000000 0x00000000 0x00000000
    0x80: 0x00000000 0x00000000 0x00000000 0x00000000
    0x90: 0x00000000 0x00000000 0x00000000 0x00000000
    0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xf0: 0x00000000 0x00000000 0x00000000 0x00000000

    Don't know how to pretty-print device-dependent header.

Sun Microsystems PCIO Happy Meal Ethernet (ethernet network, revision 
0x01) at ? dev 1 function 1 (in1
hme0: interrupting at ivec 3021
hme0: Ethernet address 08:00:20:f0:27:cf
ukphy0 at hme0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x0006b8, model 0x000c, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
esiop0 at pci0 dev 3 function 0: PCI configuration registers:
  Common header:
    0x00: 0x000f1000 0x02000047 0x01000014 0x00808c40

    Vendor Name: Symbios Logic (0x1000)
    Device Name: 53c875/876 (0x000f)
    Command register: 0x0047
      I/O space accesses: on
      Memory space accesses: on
      Bus mastering: on
      Special cycles: off
      MWI transactions: off
      Palette snooping: off
      Parity error checking: on
      Address/data stepping: off
      System error (SERR): off
      Fast back-to-back transactions: off
    Status register: 0x0200
      Capability List support: off
      66 MHz capable: off
      User Definable Features (UDF) support: off
      Fast back-to-back capable: off
      Data parity error detected: off
      DEVSEL timing: medium (0x1)
      Slave signaled Target Abort: off
      Master received Target Abort: off
      Master received Master Abort: off
      Asserted System Error (SERR): off
      Parity error detected: off
    Class Name: mass storage (0x01)
    Subclass Name: SCSI (0x00)
    Interface: 0x00
    Revision ID: 0x14
    BIST: 0x00
    Header Type: 0x00+multifunction (0x80)
    Latency Timer: 0x8c
    Cache Line Size: 0x40

  Type 0 ("normal" device) header:
    0x10: 0x00000401 0x00010000 0x00012000 0x00000000
    0x20: 0x00000000 0x00000000 0x00000000 0x00000000
    0x30: 0x00000000 0x00000000 0x00000000 0x40110100

    Base address register at 0x10
      type: 32-bit i/o
      base: 0x00000400, size: 0x00000100
    Base address register at 0x14
      type: 32-bit nonprefetchable memory
      base: 0x00010000, size: 0x00000100
    Base address register at 0x18
      type: 32-bit nonprefetchable memory
      base: 0x00012000, size: 0x00001000
    Base address register at 0x1c
      not implemented(?)
    Base address register at 0x20
      not implemented(?)
    Base address register at 0x24
      not implemented(?)
    Cardbus CIS Pointer: 0x00000000
    Subsystem vendor ID: 0x0000
    Subsystem ID: 0x0000
    Expansion ROM Base Address: 0x00000000
    Reserved @ 0x34: 0x00000000
    Reserved @ 0x38: 0x00000000
    Maximum Latency: 0x40
    Minimum Grant: 0x11
    Interrupt pin: 0x01 (pin A)
    Interrupt line: 0x00

  Device-dependent header:
    0x40: 0x00000000 0x00000000 0x00000000 0x00000000
    0x50: 0x00000000 0x00000000 0x00000000 0x00000000
    0x60: 0x00000000 0x00000000 0x00000000 0x00000000
    0x70: 0x00000000 0x00000000 0x00000000 0x00000000
    0x80: 0x00000000 0x00000000 0x00000000 0x00000000
    0x90: 0x00000000 0x00000000 0x00000000 0x00000000
    0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xf0: 0x00000000 0x00000000 0x00000000 0x00000000

    Don't know how to pretty-print device-dependent header.

Symbios Logic 53c875/876 (SCSI mass storage, revision 0x14) at ? dev 3 
function 0 (intrswiz 0, intrpi)
esiop0: using on-board RAM
esiop0: interrupting at ivec 20
esiop0: alloc new tag DSA table at PHY addr 0xfe066000
scsibus0 at esiop0: 16 targets, 8 luns per target
esiop1 at pci0 dev 3 function 1: PCI configuration registers:
  Common header:
    0x00: 0x000f1000 0x02000047 0x01000014 0x00808c40

    Vendor Name: Symbios Logic (0x1000)
    Device Name: 53c875/876 (0x000f)
    Command register: 0x0047
      I/O space accesses: on
      Memory space accesses: on
      Bus mastering: on
      Special cycles: off
      MWI transactions: off
      Palette snooping: off
      Parity error checking: on
      Address/data stepping: off
      System error (SERR): off
      Fast back-to-back transactions: off
    Status register: 0x0200
      Capability List support: off
      66 MHz capable: off
      User Definable Features (UDF) support: off
      Fast back-to-back capable: off
      Data parity error detected: off
      DEVSEL timing: medium (0x1)
      Slave signaled Target Abort: off
      Master received Target Abort: off
      Master received Master Abort: off
      Asserted System Error (SERR): off
      Parity error detected: off
    Class Name: mass storage (0x01)
    Subclass Name: SCSI (0x00)
    Interface: 0x00
    Revision ID: 0x14
    BIST: 0x00
    Header Type: 0x00+multifunction (0x80)
    Latency Timer: 0x8c
    Cache Line Size: 0x40

  Type 0 ("normal" device) header:
    0x10: 0x00000801 0x00014000 0x00016000 0x00000000
    0x20: 0x00000000 0x00000000 0x00000000 0x00000000
    0x30: 0x00000000 0x00000000 0x00000000 0x40110200

    Base address register at 0x10
      type: 32-bit i/o
      base: 0x00000800, size: 0x00000100
    Base address register at 0x14
      type: 32-bit nonprefetchable memory
      base: 0x00014000, size: 0x00000100
    Base address register at 0x18
      type: 32-bit nonprefetchable memory
      base: 0x00016000, size: 0x00001000
    Base address register at 0x1c
      not implemented(?)
    Base address register at 0x20
      not implemented(?)
    Base address register at 0x24
      not implemented(?)
    Cardbus CIS Pointer: 0x00000000
    Subsystem vendor ID: 0x0000
    Subsystem ID: 0x0000
    Expansion ROM Base Address: 0x00000000
    Reserved @ 0x34: 0x00000000
    Reserved @ 0x38: 0x00000000
    Maximum Latency: 0x40
    Minimum Grant: 0x11
    Interrupt pin: 0x02 (pin B)
    Interrupt line: 0x00

  Device-dependent header:
    0x40: 0x00000000 0x00000000 0x00000000 0x00000000
    0x50: 0x00000000 0x00000000 0x00000000 0x00000000
    0x60: 0x00000000 0x00000000 0x00000000 0x00000000
    0x70: 0x00000000 0x00000000 0x00000000 0x00000000
    0x80: 0x00000000 0x00000000 0x00000000 0x00000000
    0x90: 0x00000000 0x00000000 0x00000000 0x00000000
    0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xf0: 0x00000000 0x00000000 0x00000000 0x00000000

    Don't know how to pretty-print device-dependent header.

Symbios Logic 53c875/876 (SCSI mass storage, revision 0x14) at ? dev 3 
function 1 (intrswiz 0, intrpi)
esiop1: using on-board RAM
esiop1: interrupting at ivec 26
esiop1: alloc new tag DSA table at PHY addr 0xfe068000
scsibus1 at esiop1: 16 targets, 8 luns per target
psycho1 at mainbus0 addr 0xfffc6000
SUNW,psycho: impl 0, version 4: ign 7c0 bus range 128 to 128; PCI bus 128
extent `psycho mem' (0x0 - 0x7fffffff), flags = 0x0
     0x0 - 0xfff
extent `psycho io' (0x0 - 0xffff), flags = 0x0
     0x0 - 0x3ff
pci1 at psycho1
pci1: i/o space, memory space enabled
PCI configuration registers:
  Common header:
    0x00: 0x8000108e 0x02a00046 0x06000000 0x00004000

    Vendor Name: Sun Microsystems (0x108e)
    Device Name: psycho PCI controller (0x8000)
    Command register: 0x0046
      I/O space accesses: off
      Memory space accesses: on
      Bus mastering: on
      Special cycles: off
      MWI transactions: off
      Palette snooping: off
      Parity error checking: on
      Address/data stepping: off
      System error (SERR): off
      Fast back-to-back transactions: off
    Status register: 0x02a0
      Capability List support: off
      66 MHz capable: on
      User Definable Features (UDF) support: off
      Fast back-to-back capable: on
      Data parity error detected: off
      DEVSEL timing: medium (0x1)
      Slave signaled Target Abort: off
      Master received Target Abort: off
      Master received Master Abort: off
      Asserted System Error (SERR): off
      Parity error detected: off
    Class Name: bridge (0x06)
    Subclass Name: host (0x00)
    Interface: 0x00
    Revision ID: 0x00
    BIST: 0x00
    Header Type: 0x00 (0x00)
    Latency Timer: 0x40
    Cache Line Size: 0x00

  Type 0 ("normal" device) header:
    0x10: 0x00000000 0x00000000 0x00000000 0x00000000
    0x20: 0x00000000 0x00000000 0x00000000 0x00000000
    0x30: 0x00000000 0x00000000 0x00000000 0x00000000

    Base address register at 0x10
      not implemented(?)
    Base address register at 0x14
      not implemented(?)
    Base address register at 0x18
      not implemented(?)
    Base address register at 0x1c
      not implemented(?)
    Base address register at 0x20
      not implemented(?)
    Base address register at 0x24
      not implemented(?)
    Cardbus CIS Pointer: 0x00000000
    Subsystem vendor ID: 0x0000
    Subsystem ID: 0x0000
    Expansion ROM Base Address: 0x00000000
    Reserved @ 0x34: 0x00000000
    Reserved @ 0x38: 0x00000000
    Maximum Latency: 0x00
    Minimum Grant: 0x00
    Interrupt pin: 0x00 (none)
    Interrupt line: 0x00

  Device-dependent header:
    0x40: 0x0000ff80 0x00000000 0x00000000 0x00000000
    0x50: 0x00000000 0x00000000 0x00000000 0x00000000
    0x60: 0x00000000 0x00000000 0x00000000 0x00000000
    0x70: 0x00000000 0x00000000 0x00000000 0x00000000
    0x80: 0x8000108e 0x02a00046 0x06000000 0x00004000
    0x90: 0x00000000 0x00000000 0x00000000 0x00000000
    0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xc0: 0x0000ff80 0x00000000 0x00000000 0x00000000
    0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
    0xf0: 0x00000000 0x00000000 0x00000000 0x00000000

    Don't know how to pretty-print device-dependent header.

timer0 at mainbus0 addr 0xfff9fc00 irq vectors 7ec and 7ed
pcons at mainbus0 not configured
wskbd0 at kbd0 mux 1
kbd0: reset failed
raidattach: Asked for 8 units
Kernelized RAIDframe activated
scsibus0: waiting 2 seconds for devices to settle...
scsibus1: waiting 2 seconds for devices to settle...
esiop0: alloc newcdb at PHY addr 0xfe06a000
probe(esiop0:0:0:0): command timeout, CDB: 0x12 00 00 00 24 00

#############################################################################

ok .properties
available                82000000 00000000 00001000 00000000
                         7ffff000 81000000 00000000 00000400
                         00000000 0000fc00 00006176 61696c61
bus-range                00000000
                         00000000
scsi-initiator-id        00000007
version#                 00 00 00 04
implementation#          00 00 00 00
address                  fffb4000
                         fffb2000
                         fffa4000
interrupt-map            00000800 00000000 00000000 00000001 f00602e8 
00000021
                         00001000 00000000 00000000 00000001 f00602e8 
00000010
                         00001000 00000000 00000000 00000002 f00602e8 
00000011
                         00001000 00000000 00000000 00000003 f00602e8 
00000012
                         00001000 00000000 00000000 00000004 f00602e8 
00000013
                         00001800 00000000 00000000 00000001 f00602e8 
00000020
                         00001800 00000000 00000000 00000002 f00602e8 
00000026
                         00002000 00000000 00000000 00000001 f00602e8 
00000018
                         00002000 00000000 00000000 00000002 f00602e8 
00000019
                         00002000 00000000 00000000 00000003 f00602e8 
0000001a
                         00002000 00000000 00000000 00000004 f00602e8 
0000001b
                         00002800 00000000 00000000 00000001 f00602e8 
0000001c
                         00002800 00000000 00000000 00000002 f00602e8 
0000001d
                         00002800 00000000 00000000 00000003 f00602e8 
0000001e
                         00002800 00000000 00000000 00000004 f00602e8 
0000001f
interrupt-map-mask       00fff800 00000000 00000000 00000007
#interrupt-cells         00000001
slot-names               00 00 00 34 70 63 69 62 20 73 6c 6f 74 20 32 00
no-probe-list            0
clock-frequency          01f78a40
upa-portid               0000001f
interrupts               000007f1
                         000007ee
                         000007ef
                         000007e5
                         000007e8
                         000007f2
ranges                   00000000 00000000 00000000 000001fe 01000000 
00000000 00800000
                         01000000 00000000 00000000 000001fe 02010000 
00000000 00010000
                         02000000 00000000 00000000 000001ff 80000000 
00000000 80000000
                         03000000 00000000 00000000 000001ff 80000000 
00000000 80000000
reg                      000001fe 00004000 00000000 00002000
                         000001fe 01000000 00000000 00000100
                         000001fe 00000000 00000000 0000d000
bus-parity-generated    
#size-cells              00000002
#address-cells           00000003
device_type              pci
name                     pci
model                    SUNW,psycho
compatible               70 63 69 31 30 38 65 2c 38 30 30 30 00 70 63 69
thermal-interrupt
ok cd scsi@3
ok .properties
assigned-addresses       81001810 00000000 00000400 00000000 00000100
                         82001814 00000000 00010000 00000000 00000100
                         82001818 00000000 00012000 00000000 00001000
device_type              scsi-2
clock-frequency          02625a00
reg                      00001800 00000000 00000000 00000000 00000000
                         01001810 00000000 00000000 00000000 00000100
                         02001814 00000000 00000000 00000000 00000100
                         02001818 00000000 00000000 00000000 00001000
model                    Symbios,53C875
compatible               glm
name                     scsi
devsel-speed             00000001
class-code               00010000
interrupts               00000001
max-latency              00000040
min-grant                00000011
revision-id              00000014
device-id                0000000f
vendor-id                00001000
ok cd scsi@3,1
ok .properties
assigned-addresses       81001910 00000000 00000800 00000000 00000100
                         82001914 00000000 00014000 00000000 00000100
                         82001918 00000000 00016000 00000000 00001000
device_type              scsi-2
clock-frequency          02625a00
reg                      00001900 00000000 00000000 00000000 00000000
                         01001910 00000000 00000000 00000000 00000100
                         02001914 00000000 00000000 00000000 00000100
                         02001918 00000000 00000000 00000000 00001000
model                    Symbios,53C875
compatible               glm
name                     scsi
devsel-speed             00000001
class-code               00010000
interrupts               00000002
max-latency              00000040
min-grant                00000011
revision-id              00000014
device-id                0000000f
vendor-id                00001000
ok