Subject: Re: Sun 3/160 installation
To: None <port-sun3@netbsd.org>
From: Chris Rupnik <chrisr@geeknet.montreal.qc.ca>
List: port-sun3
Date: 09/07/1998 23:26:56
More information on that one,
If i remove the xyc board, the machine boots. So if there is only the CPU
card in the cardcage, the machine boots fine. As soon as i place a card,
be it a memory or the xyc card, then the machine fails to boot. This means
that i have the cardcage misconfigured, right?
I have read the sun hardware FAQ, and have the following
jumpered and not jumpered on the back of the backplane
slot 1 cpu 3&4 unjumpered
slot 2 mem 3&4 jumpered
slot 3 mem 3&4 jumpered
slot 4 mem 3&4 jumpered
slot 5 empty 3&4 jumpered
slot 6 empty 3&4 jumpered
slot 7 xyc 3&4 unjumpered
slot 8-11 empty 3&4 jumpered
slot 11 empty 4 unjumpered
Note, that the slot 11 has been tried with jumpered and unjumpered.
I must be doing something wrong.
Chris
On Mon, 7 Sep 1998, Chris Rupnik wrote:
> Hi
> Well, to follow up on the problems that i was having earlier
>
> I have since discovered that there is 4MB on the main board. There are
> three additional 4MB VME boards placed next to it. IF i remove all three
> boards, the machine will not fail with a parity error. If i place ANY of
> the three boards (properly jumpered) in the next slot, it will fail. Now,
> this is the deskside chassis, and when i remove the boards, i see no room
> for any terminators on the backplace. Where do i put them? Where are they?
>
> Anyway, i went ahead with just 4mb, just too see where i got.
> This is it
>
> NetBSD 1.3 (GENERIC) #1: Tue Jan 6 17:49:41 EST 1998
> gwr@venus:/usr/obj/sys/arch/sun3/compile/GENERIC
> Model: Sun 3/160 (hostid 11002c9a)
> fpu: mc68881
> real mem = 4096K (0x400000)
> avail mem = 2472K (0x26a000)
> using 38 buffers containing 311296 bytes of memory
> mainbus0 (root)
> obio0 at mainbus0
> zsc0 at obio0 addr 0x0 level 6: (softpri 3)
> kbd0 at zsc0 channel 0
> ms0 at zsc0 channel 1
> zsc1 at obio0 addr 0x20000 level 6: (softpri 3)
> zstty0 at zsc1 channel 0 (console)
> zstty1 at zsc1 channel 1
> zsc1: enabling zs interrupts
> eeprom0 at obio0 addr 0x40000
> clock0 at obio0 addr 0x60000 level 5
> memerr0 at obio0 addr 0x80000 level 7: (ECC memory)
> intreg0 at obio0 addr 0xa0000
> ie0 at obio0 addr 0xc0000 level 3: macaddr 08:00:20:01:99:dc
> obmem0 at mainbus0
> bwtwo0 at obmem0 addr 0xff000000 (1152x900)
> vmes0 at mainbus0
> xyc0 at vmes0 addr 0xffffee40 level 2 vect 0x48trap type=0x0, code=0x155,
> v=0xe5
> kernel: Bus error trap
> pid = 0, pc = 0E0C6982, ps = 2500, sfc = 1, dfc = 1
> Registers:
> 0 1 2 3 4 5 6
> 7
> dreg: 003D08F2 00000078 003D08F1 00000000 0FFC8030 00000000 00000000
> 0E562A40
> areg: 0FFC8030 0FFC8030 0ED1CE40 0E561980 0E115EC0 0E0DBBD4 0E115C9C
> 0DFFFFFC
>
> Kernel stack (0E115BA0):
> 115BA0: 0E0AA5B0 0E115BF4 00000080 003D08F1 00000000 0FFC8030 00000000
> 00000000
> 115BC0: 0E562A40 0ED1CE40 0E561980 0E115EC0 0E0DBBD4 0FFC8000 00000000
> 00000000
> 115BE0: 0E115C9C 0E0040E4 00000000 00000155 0ED1CE45 003D08F2 00000078
> 003D08F1
> 115C00: 00000000 0FFC8030 00000000 00000000 0E562A40 0FFC8030 0FFC8030
> 0ED1CE40
> 115C20: 0E561980 0E115EC0 0E0DBBD4 0E115C9C 0DFFFFFC 00000000 25000E0C
> 6982B008
> 115C40: 1E6C0155 6C144878 0ED1CE45 0ED1CE45 003D08F2 102A0005 0E0C698A
> 0E0C6988
> 115C60: 0E0C6986 0E0C69FF 0005FF0D 000F0487 003D08F2 00000007 003D0900
> 0000003D
> 115C80: 80200000 0ED1CE45 00000000 00000000 0E115C8C 00000030 0E55F668
> 0E115CBC
> 115CA0: 0E0C6F6C 0ED1CE40 003D0900 00000030 00000030 0E55F668 0E561980
> 0E115CD8
> 115CC0: 0E0C6DDE 0E561980 0E55F668 00000030 0E55F668 0E561980 0E115D08
> 0E0C6AB8
> 115CE0: 0E561980 0E55F668 00000030 00000004 00000002 0E561980 0FFC8030
> 0E0DBBD4
> 115D00: 0E561980 0000009C 0E115D54 0E0C5A40 0E561980 0000000C 00000000
> 00000000
> 115D20: 00000000 00000000 00000000 00000030 00000000 00000000 0E115D9E
> 00000000
> 115D40: 0E0D3470 0E0D346C 0E561980 0E0DBBD4 0E561980 0E115DA0 0E01CB36
> 0E562A40
> 115D60: 0E561980 0E115EC0 0E115EC0 0E562A40 0E115E76 00000000 0E0DABC0
> 0E562C80
> 115D80: 0E0D3350 0E0D3350 0E562A40 0E0DABC0 0E0C0E0D BBE00002 FFFFEE45
> 00003000
> panic: Bus error
> Stopped at _Debugger+0x6: unlk a6
> db> help
> machine print examine x search set
> write
> w delete d break dwatch watch
> step
> s continue c until next match
> trace
> call ps kill callout reboot show
> db> trace
> _Debugger(2504,e115be0,e0aa5ce,e0aa220,3d08f1) + 6
> _panic(e0aa220,3d08f1,0,ffc8030,0) + 40
> _trap(0,155,ed1ce45) + 1fa
> faultstkadj(ed1ce40,3d0900) + 0
> _xyc_piodriver(e561980,e55f668,30,e55f668,e561980) + 1e
> _xyc_submit_iorq(e561980,e55f668,30,4,2) + 14e
> _xyc_cmd(e561980,c,0,0,0,0,0,30) + e2
> _xycattach(e562a40,e561980,e115ec0,e115ec0,e562a40) + 1b6
> _config_attach(e562a40,e0d3350,e115ec0,e0a4b0e,e115ec0) + 276
> _bus_scan(e562a40,e0d3350,e115ec0,e0d2fcc,e0d3350) + 64
> _mapply(e115dfc,e0d3350) + 3c
> _config_search(e0a4a74,e562a40,e115ec0,0,0) + 56
> _vme_attach(e562c80,e562a40,e115ec0,e115ec0,e562c80) + 24
> _config_attach(e562c80,e0d305c,e115ec0,0,e0dab60) + 276
> _config_found_sm(e562c80,e115ec0,0,0) + 30
> _main_attach(0,e562c80,0,e0a47f8,0) + 32
> _config_attach(0,e0d3008,0,0,26a000) + 276
> _config_rootfound(e0a47f8,0) + 3a
> _configure(107,0,dc62c,f2bc,400000) + a
> _cpu_startup(107,0,dc62c,dfffffc,116db) + 2fc
> _main(e115fb0) + 4c
> db>
>
> Would this be due to the machine not being setup properly with jumpers
> and such? There is a 501-1166 in slot #7.
>
> Thanks
>
> Chris
>
>