Re: Hardware-Empfehlung für NetBSD-Router

[Uwe Klaus <uklaus%hgb-leipzig.de@localhost>]

On Thu, 2 Dec 2010, Jens Rehsack wrote:

Hallo,
> ich gedenke in nächster Zeit meinen Router durch ein neues Gerät zu
> ersetzen. Auf dem neuen Router soll idealerweise NetBSD laufen.
>
> Ich suche daher ein Gerät, das mindestens 4 unabhängig ansteuerbare
> Netzwerkports hat, möglichst wenig Strom verbraucht und von NetBSD
> unterstützt wird.
>
> Eine Konsole irgendeiner Art wäre gut, falls man mal nicht via ssh
> draufkommt, wenn was abgeraucht ist.
>
> Hat jemand eine Empfehlung, was man da nehmen könnte?
wenn der Stromverbrauch einer Atom-CPU N270 akzeptabel ist, dann kann ich
einen Lanner FW-7530B empfehlen (dmesg s.u.)
http://www.lannerinc.com/Network_Security/FW-7530
Hat sechs Intel-GB-Netzwerk-Ports und eine serielle Konsole.
Bezugsquellen:
 www.bytemine.net
 www.landitec.com

Beste Grüße
U. Klaus

------------------ dmesg --------------------
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004
, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1_RC4 (GENERIC.gw) #1: Tue Sep 14 09:37:11 CEST 2010
        root@hgb2:/usr/obj.i386/sys/arch/i386/compile/GENERIC.gw
total memory = 2039 MB
avail memory = 1992 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
To Be Filled By O.E.M. To Be Filled By O.E.M. (To Be Filled By O.E.M.)
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 1596MHz, id 0x106c2
cpu0: Enhanced SpeedStep (1324 mV) 1600 MHz
cpu0: Enhanced SpeedStep frequencies available (MHz): 1600 1467 1333 1200 
1067 933 800
cpu1 at mainbus0 apid 1: Intel 686-class, 1596MHz, id 0x106c2
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <112509,RSDT0939,20091125>, AslId <MSFT,00000097>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800): io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
npx1 at acpi0 (COPR, PNP0C04): io 0xf0-0xff irq 13
npx1: reported by CPUID; using exception 16
UAR1 (PNP0501) at acpi0 not configured
UAR2 (PNP0501) at acpi0 not configured
LPTE (PNP0400) at acpi0 not configured
FWH (INT0800) at acpi0 not configured
acpibut0 at acpi0 (PWRB, PNP0C0C-170): ACPI Power Button
apm0 at acpi0: Power Management spec V1.2
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x27ac (rev. 0x03)
agp0 at pchb0: detected 7932k stolen memory
agp0: aperture at 0xd0000000, size 0x10000000
vga1 at pci0 dev 2 function 0: vendor 0x8086 product 0x27ae (rev. 0x03)
wsdisplay0 at vga1 kbdmux 1
wsmux1: connecting to wsdisplay0
drm at vga1 not configured
vendor 0x8086 product 0x27a6 (miscellaneous display, revision 0x03) at 
pci0 dev 2 function 1
 not configured
ppb0 at pci0 dev 28 function 0: vendor 0x8086 product 0x27d0 (rev. 0x02)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
wm0 at pci1 dev 0 function 0: Intel i82574L, rev. 0
wm0: interrupting at ioapic0 pin 16
wm0: PCI-Express bus
wm0: 256 word (8 address bits) SPI EEPROM
wm0: Ethernet address 00:90:0b:XX:XX:XX
ukphy0 at wm0 phy 1: Generic IEEE 802.3u media interface
ukphy0: OUI 0x000ac2, model 0x000b, rev. 1
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb1 at pci0 dev 28 function 1: vendor 0x8086 product 0x27d2 (rev. 0x02)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
wm1 at pci2 dev 0 function 0: Intel i82574L, rev. 0
wm1: interrupting at ioapic0 pin 17
wm1: PCI-Express bus
wm1: 256 word (8 address bits) SPI EEPROM
wm1: Ethernet address 00:90:0b:XX:XX:XX
ukphy1 at wm1 phy 1: Generic IEEE 802.3u media interface
ukphy1: OUI 0x000ac2, model 0x000b, rev. 1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb2 at pci0 dev 28 function 2: vendor 0x8086 product 0x27d4 (rev. 0x02)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
wm2 at pci3 dev 0 function 0: Intel i82574L, rev. 0
wm2: interrupting at ioapic0 pin 18
wm2: PCI-Express bus
wm2: 256 word (8 address bits) SPI EEPROM
wm2: Ethernet address 00:90:0b:XX:XX:XX
ukphy2 at wm2 phy 1: Generic IEEE 802.3u media interface
ukphy2: OUI 0x000ac2, model 0x000b, rev. 1
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ppb3 at pci0 dev 28 function 3: vendor 0x8086 product 0x27d6 (rev. 0x02)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
wm3 at pci4 dev 0 function 0: Intel i82574L, rev. 0
wm3: interrupting at ioapic0 pin 19
wm3: PCI-Express bus
wm3: 256 word (8 address bits) SPI EEPROM
wm3: Ethernet address 00:90:0b:XX:XX:XX
ukphy3 at wm3 phy 1: Generic IEEE 802.3u media interface
ukphy3: OUI 0x000ac2, model 0x000b, rev. 1
ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x27c8 (rev. 0x02)
uhci0: interrupting at ioapic0 pin 23
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x27c9 (rev. 0x02)
uhci1: interrupting at ioapic0 pin 19
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x27ca (rev. 0x02)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x27cb (rev. 0x02)
uhci3: interrupting at ioapic0 pin 16
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x27cc (rev. 0x02)
ehci0: interrupting at ioapic0 pin 23
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb4 at pci0 dev 30 function 0: vendor 0x8086 product 0x2448 (rev. 0xe2)
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled
wm4 at pci5 dev 2 function 0: Intel i82541PI 1000BASE-T Ethernet, rev. 5
wm4: interrupting at ioapic0 pin 18
wm4: 32-bit 33MHz PCI bus
wm4: 64 word (6 address bits) MicroWire EEPROM
wm4: Ethernet address 00:90:0b:XX:XX:XX
igphy0 at wm4 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
wm5 at pci5 dev 3 function 0: Intel i82541PI 1000BASE-T Ethernet, rev. 5
wm5: interrupting at ioapic0 pin 19
wm5: 32-bit 33MHz PCI bus
wm5: 64 word (6 address bits) MicroWire EEPROM
wm5: Ethernet address 00:90:0b:XX:XX:XX
igphy1 at wm5 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x27b9 (rev. 0x02)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 82801GB/GR IDE Controller (ICH7) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
ahcisata0 at pci0 dev 31 function 2: vendor 0x8086 product 0x27c5
ahcisata0: interrupting at ioapic0 pin 19
ahcisata0: AHCI revision 1.1, 4 ports, 32 command slots, features 
0xc710e000
atabus1 at ahcisata0 channel 0
atabus2 at ahcisata0 channel 2
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x27da (rev. 
0x02)
ichsmb0: interrupting at ioapic0 pin 19
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
uhub0 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub1: 2 ports with 2 removable, self powered
uhub2 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 
1
uhub3: 2 ports with 2 removable, self powered
uhub4 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 
1
uhub4: 8 ports with 8 removable, self powered
ahcisata0 port 0: device present, speed: 1.5Gb/s
wd0 at atabus1 drive 0: <KINGSTON SNVP325S2128GB>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 119 GB, 248085 cyl, 16 head, 63 sec, 512 bytes/sect x 250069680 
sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(ahcisata0:0:0): using PIO mode 4, DMA mode 2, Ultra-DMA mode 5 
(Ultra/100) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex, playback, capture
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)