Subject: Great Success .... dmesg!
To: None <tech-kern@netbsd.org>
From: Zafer Aydogan <zafer@gmx.org>
List: tech-kern
Date: 07/06/2004 09:24:48
Dear Newsgroup,
below, the dmesg dump from my Server running 2.0 Kernel.
I think 2.0 is getting to become one of best Releases ever.
But that's not all. This Server was also the winner of a benchmark test
between FreeBSD 4.10 and SuSE Linux 9.1. (I only tested the Harddisk
throughput). And least but not last, NetBSD is running fine with current
SATA-RAID Controllers (in my case: 3Ware) and current onboard
Gigabit-Ethernet Adapters (Intel).
By the way, the Mainboard is a Tyan 7250.
dmesg:
NetBSD 2.0E (ZGEN) #0: Wed May 12 12:56:04 CEST 2004
zafer@t2.aydogan.net:/usr/obj/sys/arch/i386/compile/ZGEN
total memory = 1023 MB
avail memory = 994 MB
BIOS32 rev. 0 found at 0xfacb0
mainbus0 (root)
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel (686-class), 2400.20 MHz, id 0xf33
cpu0: features bfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR>
cpu0: features bfebfbff<PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX>
cpu0: features bfebfbff<FXSR,SSE,SSE2,SS,HTT,TM,SBF>
cpu0: features2 41d<CID>
cpu0: "Intel(R) Pentium(R) 4 CPU 2.40GHz"
cpu0: I-cache 12K uOp cache 8-way
cpu0: L2 cache 1 MB 64b/line 8-way
cpu0: ITLB 4K/4M: 128 entries
cpu0: DTLB 4K/4M: 64 entries
cpu0: running without thermal monitor!
cpu0: 32 page colors
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok pchb0 at
pci0 dev 0 function 0
pchb0: Intel 82875P Host (rev. 0x02)
ppb0 at pci0 dev 3 function 0: Intel product 0x257b (rev. 0x02) pci1 at ppb0
bus 1
pci1: i/o space, memory space enabled
wm0 at pci1 dev 1 function 0: Intel i82547GI 1000BASE-T Ethernet, rev. 0
wm0: interrupting at irq 5
wm0: 32-bit 33MHz PCI bus
wm0: 65536 word (16 address bits) SPI EEPROM
wm0: Ethernet address 00:e0:81:61:95:42
igphy0 at wm0 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto ppb1 at pci0 dev 28 function 0: Intel product 0x25ae
(rev. 0x02) pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
twe0 at pci2 dev 3 function 0: 3ware Escalade
twe0: interrupting at irq 9
twe0: 2 ports, Firmware FE7S 1.05.00.065, BIOS BE7X 1.08.00.048
twe0: Monitor ME7X 1.01.00.038, PCB Rev5 , Achip 3.20 , Pchip 1.30-66
twe0: port 0: WDC WD1200JD-00GBB0 114473 MB
twe0: port 1: WDC WD1200JD-00GBB0 114473 MB
ld0 at twe0 unit 0: TwinStor, status: Initializing
ld0: 111 GB, 14593 cyl, 255 head, 63 sec, 512 bytes/sect x 234439600 sectors
uhci0 at pci0 dev 29 function 0: Intel product 0x25a9 (rev. 0x02)
uhci0: interrupting at irq 12
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: Intel product 0x25aa (rev. 0x02)
uhci1: interrupting at irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
Intel product 0x25ab (miscellaneous system, revision 0x02) at pci0 dev 29
function 4 not configured Intel product 0x25ac (interrupt system, interface
0x20, revision 0x02) at pci0 dev 29 function 5 not configured Intel product
0x25ad (USB serial bus, interface 0x20, revision 0x02) at pci0 dev 29
function 7 not configured ppb2 at pci0 dev 30 function 0: Intel 82801BA
Hub-to-PCI Bridge (rev. 0x0a) pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled
vga1 at pci3 dev 1 function 0: ATI Technologies Rage XL (rev. 0x27)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
wm1 at pci3 dev 2 function 0: Intel i82541GI 1000BASE-T Ethernet, rev. 0
wm1: interrupting at irq 9
wm1: 32-bit 33MHz PCI bus
wm1: 64 word (6 address bits) MicroWire EEPROM
wm1: Ethernet address 00:e0:81:61:95:43
igphy1 at wm1 phy 1: Intel IGP01E1000 Gigabit PHY, rev. 0
igphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT,
1000baseT-FDX, auto pcib0 at pci0 dev 31 function 0
pcib0: Intel product 0x25a1 (rev. 0x02)
piixide0 at pci0 dev 31 function 1
piixide0: Intel 6300ESB IDE Controller (ICH5) (rev. 0x02)
piixide0: bus-master DMA support present
piixide0: primary channel wired to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel wired to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
Intel product 0x25a4 (SMBus serial bus, revision 0x02) at pci0 dev 31
function 3 not configured isa0 at pcib0 lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo com1 at isa0
port 0x2f8-0x2ff irq 3: ns16550a, working fifo com2 at isa0 port 0x3e8-0x3ef
irq 5: ns16550a, working fifo
intr_establish: pic pic0 pin 5: can't share type 3 with 2 pckbc0 at isa0
port 0x60-0x64 pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support npx0 at isa0
port 0xf0-0xff: using exception 16 fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
fd0 at fdc0 drive 0: 1.44MB, 80 cyl, 2 head, 18 sec
Kernelized RAIDframe activated
atapibus0 at atabus0: 2 targets
cd0 at atapibus0 drive 0: <TOSHIBA ODD-DVD SD-M1802, , 1031> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA
data transfers) boot device: ld0 root on ld0a dumps on ld0b root file system
type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
twe0: unit 0: initialization started
twe0: unit 0: initialization done
$ ifconfig -a
wm0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
capabilities=7<IP4CSUM,TCP4CSUM,UDP4CSUM>
enabled=0<>
address: 00:e0:81:61:95:42
media: Ethernet autoselect (100baseTX full-duplex)
status: active
inet 192.168.254.211 netmask 0xffffff00 broadcast 192.168.254.255
inet6 fe80::2e0:81ff:fe61:9542%wm0 prefixlen 64 scopeid 0x1
wm1: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
capabilities=7<IP4CSUM,TCP4CSUM,UDP4CSUM>
enabled=0<>
address: 00:e0:81:61:95:43
media: Ethernet autoselect (none)
status: no carrier
inet 0.0.0.0 netmask 0xff000000 broadcast 255.255.255.255
inet6 fe80::2e0:81ff:fe61:9543%wm1 prefixlen 64 scopeid 0x2
lo0: flags=8009<UP,LOOPBACK,MULTICAST> mtu 33196
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x3
ppp0: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
ppp1: flags=8010<POINTOPOINT,MULTICAST> mtu 1500
sl0: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 296
sl1: flags=c010<POINTOPOINT,LINK2,MULTICAST> mtu 296
strip0: flags=0<> mtu 1100
strip1: flags=0<> mtu 1100
-bash-2.05b$
Install:
If you select "whole disk" during Installation, NetBSD is not able to boot,
because it installs itself in the 3rd Hard Disk Partition.
If you select "part of disk" and then choose the 1st Partition 0 then,
everything works fine.
Frag Size & Block Size:
This was the first time, I saw, that NetBSD could not newfs. I had to change
the frag & blocksize. (this should be done automatically)
There were two 120GB running RAID 0 (mirror) recognized as ld0.
But I already had another Server with a single 120GB Disk, though that i was
surprised that this error showed up.
With best regards,
Zafer Aydogan.