Subject: pcmcia io alloc and map (can this be right?)
To: NetBSD-current <current-users@netbsd.org>
From: Sverre Froyen <sverre@viewmark.com>
List: tech-kern
Date: 02/18/2006 11:41:31
--Boundary-00=_bp29Dp16UKuPQrs
Content-Type: text/plain;
charset="us-ascii"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline
Hi,
With a pcmcia modem card (which does not work with NetBSD) I observe the
following from the dmesg output (attached):
The function pcmcia_function_configure is called. It calls the following
functions with the attendant dmesg output in parenthesis:
pcmcia_config_alloc
pccbb_pcmcia_io_alloc
rbus_space_alloc
(addr 3f8, size 8, mask 3ff, align 400)
(alloc port 0x4000+0x8)
pcmcia_config_map
pcmcia_io_map
pccbb_pcmcia_io_map
(window 0 io8 port 4000+8)
pccbb_pcmcia_do_io_map
(win 0 addr 0x4000 size 0x8 width 8)
(start 00 40, stop 07 40, ioctl 00 enable 40)
When attempting to read or write to the modem, the bus_space read and write
functions are using a bus_space_tag_t value of 0 (IO space) and a bus_addr_t
value of 0x43f8. This appears to conflict with the dmesg output from
pccbb_pcmcia_io_alloc which says the address space ranges from 0x4000 to
0x4008 (not including 0x43f8) and also with the output from
pccbb_pcmcia_do_io_map which maps the same range.
Comments and help are appreciated!
Attached is the dmesg output before inserting the modem card (dmesg) and the
additional dmesg output when the card is inserted (dmesg_pcmcia).
Thanks,
Sverre
--Boundary-00=_bp29Dp16UKuPQrs
Content-Type: text/plain;
charset="us-ascii";
name="dmesg"
Content-Transfer-Encoding: 7bit
Content-Disposition: attachment;
filename="dmesg"
NetBSD 3.99.15 (ABBOR) #0: Fri Feb 17 09:59:08 MST 2006
toor@abbor.fesk.com:/usr/src/objdir/sys/arch/i386/compile.i386/ABBOR
total memory = 510 MB
avail memory = 493 MB
BIOS32 rev. 0 found at 0xfd750
PCI BIOS rev. 2.1 found at 0xfd8d6
pcibios: config mechanism [1][x], special cycles [x][x], last bus 8
PCI IRQ Routing Table rev. 1.0 found at 0xfdea0, size 272 bytes (15 entries)
PCI Interrupt Router at 000:31:0 (Intel 82371FB (PIIX) PCI-ISA Bridge compatible)
------------------------------------------
device vendor product pin PIRQ IRQ stage
------------------------------------------
000:29:0 0x8086 0x24c2 A 0x00 11 0 already assigned
000:29:1 0x8086 0x24c4 B 0x03 11 0 already assigned
000:29:2 0x8086 0x24c7 C 0x02 11 0 already assigned
000:29:7 0x8086 0x24cd D 0x07 11 0 already assigned
000:31:1 0x8086 0x24ca A 0x02 11 0 fixed up
000:31:3 0x8086 0x24c3 B 0x01 11 0 already assigned
000:31:5 0x8086 0x24c5 B 0x01 11 0 already assigned
000:31:6 0x8086 0x24c6 B 0x01 11 0 already assigned
001:00:0 0x1002 0x4e50 A 0x00 11 0 already assigned
002:00:0 0x104c 0xac46 A 0x00 11 0 already assigned
002:00:1 0x104c 0xac46 B 0x01 11 0 already assigned
002:01:0 0x8086 0x101e A 0x00 11 0 already assigned
002:02:0 0x8086 0x4220 A 0x02 11 0 already assigned
------------------------------------------
mainbus0 (root)
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005800
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005808
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x00005810
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x0000580c
pci_addr_fixup: 000:31:1 0x8086 0x24ca new address 0x1fe00000
cpu0 at mainbus0: (uniprocessor)
cpu0: Intel Pentium M (Dothan) (686-class), 1694.57 MHz, id 0x6d6
cpu0: features afe9f9bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR>
cpu0: features afe9f9bf<PGE,MCA,CMOV,PAT,CFLUSH,DS,ACPI,MMX>
cpu0: features afe9f9bf<FXSR,SSE,SSE2,SS,TM,SBF>
cpu0: features2 180<EST,TM2>
cpu0: "Intel(R) Pentium(R) M processor 1.70GHz"
cpu0: I-cache 32 KB 64B/line 8-way, D-cache 32 KB 64B/line 8-way
cpu0: L2 cache 2 MB 64B/line 8-way
cpu0: using thermal monitor 2
cpu0: Enhanced SpeedStep running at 1700 MHz (1340 mV)
cpu0: Enhanced SpeedStep frequencies available (MHz): 1700 1400 1200 1000 800 600
cpu0: 64 page colors
acpi0 at mainbus0
acpi0: using Intel ACPI CA subsystem version 20060113
acpi0: X/RSDT: OemId <IBM ,TP-1R ,00003190>, AslId < LTP,00000000>
acpi0: found ECDT, GPE 28
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
ACPI Object Type 'Processor' (0x0c) at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C0F at acpi0 not configured
PNP0C01 at acpi0 not configured
acpilid0 at acpi0 (PNP0C0D): ACPI Lid Switch
acpibut0 at acpi0 (PNP0C0E): ACPI Sleep Button
PNP0A03 at acpi0 not configured
PNP0C02 at acpi0 not configured
PNP0000 at acpi0 not configured
attimer0 at acpi0 (PNP0100): AT Timer
attimer0: io 0x40-0x43 irq 0
PNP0200 at acpi0 not configured
pcppi0 at acpi0 (PNP0800)
pcppi0: io 0x61
midi0 at pcppi0: PC speaker
sysbeep0 at pcppi0
npx1 at acpi0 (PNP0C04)
npx1: io 0xf0 irq 13
npx1: using exception 16
PNP0B00 at acpi0 not configured
pckbc1 at acpi0 (PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
pckbc2 at acpi0 (IBM0057): aux port
pckbc2: irq 12
fdc1 at acpi0 (PNP0700)
fdc1: io 0x3f0-0x3f5,0x3f7 irq 6 drq 2
PNP0501 at acpi0 not configured
lpt3 at acpi0 (PNP0400)
lpt3: io 0x3bc-0x3be irq 7
IBM0071 at acpi0 not configured
acpiec0 at acpi0 (PNP0C09-0): ACPI Embedded Controller
acpiec0: io 0x62,0x66
ACPI Object Type 'Power' (0x0b) at acpi0 not configured
acpibat0 at acpi0 (PNP0C0A-0): ACPI Battery (Control Method)
acpiacad0 at acpi0 (ACPI0003-0): ACPI AC Adapter
IBM0068 at acpi0 not configured
acpitz0 at acpi0: ACPI Thermal Zone
acpitz0: unable to get polling interval; using default of 30.0s
acpitz0: passive cooling mode only
acpitz0: critical 93.0C passive 55.0C
pcppi0: attached to attimer0
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pms0 at pckbc1 (aux slot)
pms0: Synaptics touchpad version 5.9
pms0: Palm detect, Multi-finger
pckbc1: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0: PCI configuration registers:
Common header:
0x00: 0x33408086 0x20900106 0x06000003 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82855PM MCH Host Controller (0x3340)
Command register: 0x0106
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x2090
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: fast (0x0)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: on
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: host (0x00)
Interface: 0x00
Revision ID: 0x03
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0xd0000008 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x05291014
0x30: 0x00000000 0x000000e4 0x00000000 0x00000000
Base address register at 0x10
type: 32-bit prefetchable memory
base: 0xd0000000, not sized
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x0529
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0xe4
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Capability register at 0xe4
type: 0x09 (Vendor-specific)
Capability register at 0xa0
type: 0x02 (AGP, rev. 2.0)
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00002700
0x60: 0x10100804 0x00000000 0x00000000 0x00000000
0x70: 0x00000302 0x00000000 0x2d020000 0x30403271
0x80: 0x05800071 0x00000000 0x00011000 0x00000000
0x90: 0x01111110 0x00111130 0x00001941 0x007d1a00
0xa0: 0x00200002 0x1f000217 0x00000001 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00001020
0xc0: 0x11504044 0x06052000 0x00000000 0x00000000
0xd0: 0x0e002802 0x3000000b 0xb5310000 0x00020000
0xe0: 0x00000000 0x4104a009 0x00000000 0x00000000
0xf0: 0x00010000 0x8020f874 0x00210f38 0x00000004
Don't know how to pretty-print device-dependent header.
Intel 82855PM MCH Host Controller (host bridge, revision 0x03) at ? dev 0 function 0 (tag 0x80000000, intrtag 0x80000000, intrswiz 0, intrpin 0, i/o off, mem on, no quirks)
pchb0: Intel 82855PM MCH Host Controller (rev. 0x03)
agp0 at pchb0: aperture at 0xd0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0: PCI configuration registers:
Common header:
0x00: 0x33418086 0x00a00107 0x06040003 0x00016000
Vendor Name: Intel (0x8086)
Device Name: 82855PM Host-AGP Bridge (0x3341)
Command register: 0x0107
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x00a0
Capability List support: off
66 MHz capable: on
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: fast (0x0)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: PCI (0x04)
Interface: 0x00
Revision ID: 0x03
BIST: 0x00
Header Type: 0x01 (0x01)
Latency Timer: 0x60
Cache Line Size: 0x00
Type 1 (PCI-PCI bridge) header:
0x10: 0x00000000 0x00000000 0x40010100 0x22a03030
0x20: 0xc010c010 0xe7f0e000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x000c0000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Primary bus number: 0x00
Secondary bus number: 0x01
Subordinate bus number: 0x01
Secondary bus latency timer: 0x40
Secondary status register: 0x22a0
66 MHz capable: on
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Signaled Target Abort: off
Received Target Abort: off
Received Master Abort: on
System Error: off
Parity Error: off
I/O region:
base register: 0x30
limit register: 0x30
base upper 16 bits register: 0x0000
limit upper 16 bits register: 0x0000
Memory region:
base register: 0xc010
limit register: 0xc010
Prefetchable memory region:
base register: 0xe000
limit register: 0xe7f0
base upper 32 bits register: 0x00000000
limit upper 32 bits register: 0x00000000
Reserved @ 0x34: 0x00000000
Expansion ROM Base Address: 0x00000000
Interrupt line: 0x00
Interrupt pin: 0x00 (none)
Bridge control register: 0x000c
Parity error response: off
Secondary SERR forwarding: off
ISA enable: on
VGA enable: on
Master abort reporting: off
Secondary bus reset: off
Fast back-to-back capable: off
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x1fff95d4 0x0009f441 0x8c9408cc 0x0003fe55
0x60: 0x00000001 0x00804852 0x000000b2 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82855PM Host-AGP Bridge (PCI bridge, revision 0x03) at ? dev 1 function 0 (tag 0x80000800, intrtag 0x80000800, intrswiz 0, intrpin 0, i/o on, mem on, no quirks): Intel 82855PM Host-AGP Bridge (rev. 0x03)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled
vga1 at pci1 dev 0 function 0: PCI configuration registers:
Common header:
0x00: 0x4e501002 0x02b00307 0x03000000 0x00004208
Vendor Name: ATI Technologies (0x1002)
Device Name: Mobility Radeon 9700 (0x4e50)
Command register: 0x0307
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: on
Status register: 0x02b0
Capability List support: on
66 MHz capable: on
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: display (0x03)
Subclass Name: VGA (0x00)
Interface: 0x00
Revision ID: 0x00
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x42
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0xe0000008 0x00003001 0xc0100000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x05501014
0x30: 0x00000000 0x00000058 0x00000000 0x0008010b
Base address register at 0x10
type: 32-bit prefetchable memory
base: 0xe0000000, size: 0x08000000
Base address register at 0x14
type: 32-bit i/o
base: 0x00003000, size: 0x00000100
Base address register at 0x18
type: 32-bit nonprefetchable memory
base: 0xc0100000, size: 0x00010000
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x0550
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x58
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x08
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x0b
Capability register at 0x58
type: 0x02 (AGP, rev. 2.0)
Capability register at 0x50
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x05501014
0x50: 0x06020001 0x00000000 0x00205002 0x4f000217
0x60: 0x00000200 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000005 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
ATI Technologies Mobility Radeon 9700 (VGA display) at ? dev 0 function 0 (tag 0x80010000, intrtag 0x80000800, intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): ATI Technologies Mobility Radeon 9700 (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
uhci0 at pci0 dev 29 function 0: PCI configuration registers:
Common header:
0x00: 0x24c28086 0x02800005 0x0c030001 0x00800000
Vendor Name: Intel (0x8086)
Device Name: 82801DB USB UHCI Controller (0x24c2)
Command register: 0x0005
I/O space accesses: on
Memory space accesses: off
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00+multifunction (0x80)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00001801 0x00000000 0x00000000 0x052d1014
0x30: 0x00000000 0x00000000 0x00000000 0x0000010b
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
type: 16-bit i/o
base: 0x00001800, size: 0x00000020
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x052d
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x0b
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000010 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00002f00 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82801DB USB UHCI Controller (USB serial bus, revision 0x01) at ? dev 29 function 0 (tag 0x8000e800, intrtag 0x8000e800, intrswiz 0, intrpin 0x1, i/o on, mem off, no quirks): Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci0: interrupting at irq 11
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 29 function 1: PCI configuration registers:
Common header:
0x00: 0x24c48086 0x02800005 0x0c030001 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82801DB USB UHCI Controller (0x24c4)
Command register: 0x0005
I/O space accesses: on
Memory space accesses: off
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00001821 0x00000000 0x00000000 0x052d1014
0x30: 0x00000000 0x00000000 0x00000000 0x0000020b
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
type: 16-bit i/o
base: 0x00001820, size: 0x00000020
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x052d
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x02 (pin B)
Interrupt line: 0x0b
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000010 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00002f00 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82801DB USB UHCI Controller (USB serial bus, revision 0x01) at ? dev 29 function 1 (tag 0x8000e900, intrtag 0x8000e900, intrswiz 0, intrpin 0x2, i/o on, mem off, no quirks): Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci1: interrupting at irq 11
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2 at pci0 dev 29 function 2: PCI configuration registers:
Common header:
0x00: 0x24c78086 0x02800005 0x0c030001 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82801DB USB UHCI Controller (0x24c7)
Command register: 0x0005
I/O space accesses: on
Memory space accesses: off
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00001841 0x00000000 0x00000000 0x052d1014
0x30: 0x00000000 0x00000000 0x00000000 0x0000030b
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
type: 16-bit i/o
base: 0x00001840, size: 0x00000020
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x052d
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x03 (pin C)
Interrupt line: 0x0b
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000010 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00002f00 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82801DB USB UHCI Controller (USB serial bus, revision 0x01) at ? dev 29 function 2 (tag 0x8000ea00, intrtag 0x8000ea00, intrswiz 0, intrpin 0x3, i/o on, mem off, no quirks): Intel 82801DB USB UHCI Controller (rev. 0x01)
uhci2: interrupting at irq 11
usb2 at uhci2: USB revision 1.0
uhub2 at usb2
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 29 function 7: PCI configuration registers:
Common header:
0x00: 0x24cd8086 0x02900106 0x0c032001 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82801DB USB EHCI Controller (0x24cd)
Command register: 0x0106
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: USB (0x03)
Interface: 0x20
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0xc0000000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x052e1014
0x30: 0x00000000 0x00000050 0x00000000 0x0000040b
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0xc0000000, size: 0x00000400
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x052e
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x50
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x04 (pin D)
Interrupt line: 0x0b
Capability register at 0x50
type: 0x01 (Power Management, rev. 1.0)
Capability register at 0x58
type: 0x0a (Debug Port)
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0xc9c25801 0x00000000 0x2080000a 0x00000000
0x60: 0x001f2020 0x00000000 0x00000001 0xc0000000
0x70: 0x00010000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000001 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x003f0000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x001fbf78 0x00008388 0x00000f60 0x00000006
Don't know how to pretty-print device-dependent header.
Intel 82801DB USB EHCI Controller (USB serial bus, interface 0x20, revision 0x01) at ? dev 29 function 7 (tag 0x8000ef00, intrtag 0x8000ef00, intrswiz 0, intrpin 0x4, i/o off, mem on, no quirks): Intel 82801DB USB EHCI Controller (rev. 0x01)
ehci0: interrupting at irq 11
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2
usb3 at ehci0: USB revision 2.0
uhub3 at usb3
uhub3: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 6 ports with 6 removable, self powered
ppb1 at pci0 dev 30 function 0: PCI configuration registers:
Common header:
0x00: 0x24488086 0x80800107 0x06040081 0x00010000
Vendor Name: Intel (0x8086)
Device Name: 82801BAM Hub-PCI Bridge (0x2448)
Command register: 0x0107
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x8080
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: fast (0x0)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: on
Class Name: bridge (0x06)
Subclass Name: PCI (0x04)
Interface: 0x00
Revision ID: 0x81
BIST: 0x00
Header Type: 0x01 (0x01)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 1 (PCI-PCI bridge) header:
0x10: 0x00000000 0x00000000 0x40040200 0x22808040
0x20: 0xcff0c020 0xeff0e800 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x00040000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Primary bus number: 0x00
Secondary bus number: 0x02
Subordinate bus number: 0x04
Secondary bus latency timer: 0x40
Secondary status register: 0x2280
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Signaled Target Abort: off
Received Target Abort: off
Received Master Abort: on
System Error: off
Parity Error: off
I/O region:
base register: 0x40
limit register: 0x80
base upper 16 bits register: 0x0000
limit upper 16 bits register: 0x0000
Memory region:
base register: 0xc020
limit register: 0xcff0
Prefetchable memory region:
base register: 0xe800
limit register: 0xeff0
base upper 32 bits register: 0x00000000
limit upper 32 bits register: 0x00000000
Reserved @ 0x34: 0x00000000
Expansion ROM Base Address: 0x00000000
Interrupt line: 0x00
Interrupt pin: 0x00 (none)
Bridge control register: 0x0004
Parity error response: off
Secondary SERR forwarding: off
ISA enable: on
VGA enable: off
Master abort reporting: off
Secondary bus reset: off
Fast back-to-back capable: off
Device-dependent header:
0x40: 0x00202802 0x00000000 0x00000000 0x00000000
0x50: 0x00007402 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000040 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00080010 0x00000000 0x00000000 0x00000000
0xb0: 0x00020001 0x00c00000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x462e0000
Don't know how to pretty-print device-dependent header.
Intel 82801BAM Hub-PCI Bridge (PCI bridge, revision 0x81) at ? dev 30 function 0 (tag 0x8000f000, intrtag 0x8000f000, intrswiz 0, intrpin 0, i/o on, mem on, no quirks): Intel 82801BAM Hub-PCI Bridge (rev. 0x81)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled
cbb0 at pci2 dev 0 function 0: PCI configuration registers:
Common header:
0x00: 0xac46104c 0x02100107 0x06070001 0x00824008
Vendor Name: Texas Instruments (0x104c)
Device Name: PCI4520 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (0xac46)
Command register: 0x0107
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: CardBus (0x07)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x02+multifunction (0x82)
Latency Timer: 0x40
Cache Line Size: 0x08
Type 2 (PCI-CardBus bridge) header:
0x10: 0xb0000000 0x020000a0 0xb0030302 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x03c0010b
0x40: 0x05521014 0x000003e1
Base address register at 0x10 (CardBus socket/ExCA registers)
type: 32-bit nonprefetchable memory
base: 0xb0000000, size: 0x00001000
Capability list pointer: 0xa0
Secondary status register: 0x0200
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detection: off
DEVSEL timing: medium (0x1)
PCI target aborts terminate CardBus bus master transactions: off
CardBus target aborts terminate PCI bus master transactions: off
Bus initiator aborts terminate initiator transactions: off
System error: off
Parity error: off
PCI bus number: 0x02
CardBus bus number: 0x03
Subordinate bus number: 0x03
CardBus latency timer: 0xb0
CardBus memory region 0:
base register: 0x00000000
limit register: 0x00000000
CardBus memory region 1:
base register: 0x00000000
limit register: 0x00000000
CardBus I/O region 0:
base register: 0x00000000
limit register: 0x00000000
CardBus I/O region 1:
base register: 0x00000000
limit register: 0x00000000
Interrupt line: 0x0b
Interrupt pin: 0x01 (pin A)
Bridge control register: 0x03c0
Parity error response: off
CardBus SERR forwarding: off
ISA enable: off
VGA enable: off
CardBus master abort reporting: off
CardBus reset: on
Functional interrupts routed by ExCA registers: on
Memory window 0 prefetchable: on
Memory window 1 prefetchable: on
Write posting enable: off
Subsystem vendor ID: 0x1014
Subsystem ID: 0x0552
Base address register at 0x44 (legacy-mode registers)
type: 32-bit i/o
base: 0x000003e0, size: 0x00000004
Capability register at 0xa0
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x48: 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x0860d070 0x040a0000 0x000f0000 0x01d21b22
0x90: 0x416422c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Texas Instruments PCI4520 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (CardBus bridge, revision 0x01) at ? dev 0 function 0 (tag 0x80020000, intrtag 0x8000f000, intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks): Texas Instruments PCI4520 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (rev. 0x01) (chipflags 3)
rbus_new_body: [4000, 6000] type share name [PCI I/O port space]
rbus_new_body: [40000000, ffffffff] type share name [PCI I/O memory space]
cbb0: socket base address 0xb0000000
cbb0: using ioapic for interrupt
cbb0: intrpin A, intrtag 11
cbb1 at pci2 dev 0 function 1: PCI configuration registers:
Common header:
0x00: 0xac46104c 0x02100107 0x06070001 0x00824008
Vendor Name: Texas Instruments (0x104c)
Device Name: PCI4520 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (0xac46)
Command register: 0x0107
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x0210
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: CardBus (0x07)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x02+multifunction (0x82)
Latency Timer: 0x40
Cache Line Size: 0x08
Type 2 (PCI-CardBus bridge) header:
0x10: 0xb1000000 0x020000a0 0xb0040402 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x03c0020b
0x40: 0x05521014 0x00000001
Base address register at 0x10 (CardBus socket/ExCA registers)
type: 32-bit nonprefetchable memory
base: 0xb1000000, size: 0x00001000
Capability list pointer: 0xa0
Secondary status register: 0x0200
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detection: off
DEVSEL timing: medium (0x1)
PCI target aborts terminate CardBus bus master transactions: off
CardBus target aborts terminate PCI bus master transactions: off
Bus initiator aborts terminate initiator transactions: off
System error: off
Parity error: off
PCI bus number: 0x02
CardBus bus number: 0x04
Subordinate bus number: 0x04
CardBus latency timer: 0xb0
CardBus memory region 0:
base register: 0x00000000
limit register: 0x00000000
CardBus memory region 1:
base register: 0x00000000
limit register: 0x00000000
CardBus I/O region 0:
base register: 0x00000000
limit register: 0x00000000
CardBus I/O region 1:
base register: 0x00000000
limit register: 0x00000000
Interrupt line: 0x0b
Interrupt pin: 0x02 (pin B)
Bridge control register: 0x03c0
Parity error response: off
CardBus SERR forwarding: off
ISA enable: off
VGA enable: off
CardBus master abort reporting: off
CardBus reset: on
Functional interrupts routed by ExCA registers: on
Memory window 0 prefetchable: on
Memory window 1 prefetchable: on
Write posting enable: off
Subsystem vendor ID: 0x1014
Subsystem ID: 0x0552
Base address register at 0x44 (legacy-mode registers)
type: 32-bit i/o
base: 0x00000000, size: 0x00000004
Capability register at 0xa0
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x48: 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x0860d070 0x040a0000 0x000f0000 0x01d21b22
0x90: 0x416422c0 0x00000000 0x00000000 0x00000000
0xa0: 0xfe120001 0x00c00000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Texas Instruments PCI4520 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (CardBus bridge, revision 0x01) at ? dev 0 function 1 (tag 0x80020100, intrtag 0x8000f000, intrswiz 0, intrpin 0x2, i/o on, mem on, no quirks): Texas Instruments PCI4520 PCI-CardBus Bridge w/ IEEE 1394 Host Controller (rev. 0x01) (chipflags 3)
rbus_new_body: [4000, 6000] type share name [PCI I/O port space]
rbus_new_body: [40000000, ffffffff] type share name [PCI I/O memory space]
cbb1: socket base address 0xb1000000
cbb1: using ioapic for interrupt
cbb1: intrpin B, intrtag 11
wm0 at pci2 dev 1 function 0: PCI configuration registers:
Common header:
0x00: 0x101e8086 0x02300117 0x02000003 0x00004008
Vendor Name: Intel (0x8086)
Device Name: i82540EP Gigabit Ethernet (0x101e)
Command register: 0x0117
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: on
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x0230
Capability List support: on
66 MHz capable: on
User Definable Features (UDF) support: off
Fast back-to-back capable: off
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: ethernet (0x00)
Interface: 0x00
Revision ID: 0x03
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x40
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0xc0220000 0xc0200000 0x00008001 0x00000000
0x20: 0x00000000 0x00000000 0x00000022 0x05491014
0x30: 0x00000000 0x000000dc 0x00000000 0x00ff010b
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0xc0220000, size: 0x00020000
Base address register at 0x14
type: 32-bit nonprefetchable memory
base: 0xc0200000, size: 0x00010000
Base address register at 0x18
type: 32-bit i/o
base: 0x00008000, size: 0x00000040
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000022
Subsystem vendor ID: 0x1014
Subsystem ID: 0x0549
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0xdc
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0xff
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x0b
Capability register at 0xdc
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0xc8220001
0xe0: 0x14002000 0x00020007 0x04400000 0x00000000
0xf0: 0x00800005 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Intel i82540EP Gigabit Ethernet (ethernet network, revision 0x03) at ? dev 1 function 0 (tag 0x80020800, intrtag 0x8000f000, intrswiz 0x1, intrpin 0x2, i/o on, mem on, no quirks): Intel i82540EP 1000BASE-T Ethernet, rev. 3
wm0: interrupting at irq 11
wm0: 32-bit 33MHz PCI bus
wm0: 64 word (6 address bits) MicroWire EEPROM
wm0: Ethernet address 00:0d:60:cf:6a:aa
makphy0 at wm0 phy 1: Marvell 88E1011 Gigabit PHY, rev. 4
makphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
iwi0 at pci2 dev 2 function 0: PCI configuration registers:
Common header:
0x00: 0x42208086 0x02900116 0x02800005 0x00004008
Vendor Name: Intel (0x8086)
Device Name: PRO/Wireless LAN 2200BG Mini-PCI Adapter (0x4220)
Command register: 0x0116
I/O space accesses: off
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: on
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): on
Fast back-to-back transactions: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: network (0x02)
Subclass Name: miscellaneous (0x80)
Interface: 0x00
Revision ID: 0x05
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x40
Cache Line Size: 0x08
Type 0 ("normal" device) header:
0x10: 0xc0214000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x27118086
0x30: 0x00000000 0x000000dc 0x00000000 0x1803010b
Base address register at 0x10
type: 32-bit nonprefetchable memory
base: 0xc0214000, size: 0x00001000
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x8086
Subsystem ID: 0x2711
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0xdc
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x18
Minimum Grant: 0x03
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x0b
Capability register at 0xdc
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00008080 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0xc8220001
0xe0: 0x13002000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000000 0x00000000
Don't know how to pretty-print device-dependent header.
Intel PRO/Wireless LAN 2200BG Mini-PCI Adapter (miscellaneous network, revision 0x05) at ? dev 2 function 0 (tag 0x80021000, intrtag 0x8000f000, intrswiz 0x2, intrpin 0x3, i/o off, mem on, no quirks): Intel PRO/Wireless LAN 2200BG Mini-PCI Adapter (rev. 0x05)
iwi0: interrupting at irq 11
iwi0: 802.11 address 00:0e:35:38:b0:33
iwi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
iwi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
CardBus latency timer 0xb0 (b0030302)
PCI latency timer 0x40 (824008)
pccbb_power: CARDBUS_VCC_0V and CARDBUS_VPP_0V [0x44]
cbb0: interrupting at irq 11
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 3
pcmcia0 at cardslot0
pccbb_pcmcia_card_detect
pccbbattach: found cardslot
CardBus latency timer 0xb0 (b0040402)
PCI latency timer 0x40 (824008)
pccbb_power: CARDBUS_VCC_0V and CARDBUS_VPP_0V [0x44]
cbb1: interrupting at irq 11
cardslot1 at cbb1 slot 1 flags 0
cardbus1 at cardslot1: bus 4
pcmcia1 at cardslot1
pccbb_pcmcia_card_detect
pccbbattach: found cardslot
pcib0 at pci0 dev 31 function 0: PCI configuration registers:
Common header:
0x00: 0x24cc8086 0x0280000f 0x06010001 0x00800000
Vendor Name: Intel (0x8086)
Device Name: 82801DB ISA Bridge (0x24cc)
Command register: 0x000f
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: on
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: bridge (0x06)
Subclass Name: ISA (0x01)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00+multifunction (0x80)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x00000000
0x30: 0x00000000 0x00000000 0x00000000 0x00000000
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x0000
Subsystem ID: 0x0000
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x00 (none)
Interrupt line: 0x00
Device-dependent header:
0x40: 0x00001001 0x00000010 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00001181 0x00000010
0x60: 0x0b0b0b0b 0x00000092 0x0b80800b 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x0000fcff 0x00000000 0x00000000 0x00000000
0xa0: 0x00020224 0x00000000 0x0000000d 0x00080000
0xb0: 0x00000000 0x00000000 0x0a020000 0x00000000
0xc0: 0x00000010 0x000015e0 0x00000000 0x0000000f
0xd0: 0x00002807 0x00000f02 0x00000004 0x00000000
0xe0: 0xff000210 0x3c0f1601 0x00112233 0x45670000
0xf0: 0x00000000 0x00000000 0x00030f60 0x00800000
Don't know how to pretty-print device-dependent header.
Intel 82801DB ISA Bridge (ISA bridge, revision 0x01) at ? dev 31 function 0 (tag 0x8000f800, intrtag 0x8000f800, intrswiz 0, intrpin 0, i/o on, mem on, no quirks)
pcib0: Intel 82801DB ISA Bridge (rev. 0x01)
piixide0 at pci0 dev 31 function 1: PCI configuration registers:
Common header:
0x00: 0x24ca8086 0x02800007 0x01018a01 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82801DBM IDE Controller (0x24ca)
Command register: 0x0007
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: mass storage (0x01)
Subclass Name: IDE (0x01)
Interface: 0x8a
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00005801 0x00005809 0x00005811 0x0000580d
0x20: 0x00001861 0x1fe00000 0x00000000 0x052d1014
0x30: 0x00000000 0x00000000 0x00000000 0x0000010b
Base address register at 0x10
type: 16-bit i/o
base: 0x00005800, size: 0x00000008
Base address register at 0x14
type: 16-bit i/o
base: 0x00005808, size: 0x00000004
Base address register at 0x18
type: 16-bit i/o
base: 0x00005810, size: 0x00000008
Base address register at 0x1c
type: 16-bit i/o
base: 0x0000580c, size: 0x00000004
Base address register at 0x20
type: 16-bit i/o
base: 0x00001860, size: 0x00000010
Base address register at 0x24
type: 32-bit nonprefetchable memory
base: 0x1fe00000, size: 0x00000400
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x052d
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x01 (pin A)
Interrupt line: 0x0b
Device-dependent header:
0x40: 0xa303a307 0x00000000 0x02010005 0x00000000
0x50: 0x00000000 0x00001411 0x00000000 0x00000000
0x60: 0x00000008 0x00000000 0x00000008 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82801DBM IDE Controller (IDE mass storage, interface 0x8a, revision 0x01) at ? dev 31 function 1 (tag 0x8000f900, intrtag 0x8000f900, intrswiz 0, intrpin 0x1, i/o on, mem on, no quirks)
piixide0: Intel 82801DBM IDE Controller (ICH4-M) (rev. 0x01)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at irq 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel interrupting at irq 15
atabus1 at piixide0 channel 1
Intel 82801DB SMBus Controller (SMBus serial bus, revision 0x01) at pci0 dev 31 function 3: PCI configuration registers:
Common header:
0x00: 0x24c38086 0x02800001 0x0c050001 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82801DB SMBus Controller (0x24c3)
Command register: 0x0001
I/O space accesses: on
Memory space accesses: off
Bus mastering: off
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0280
Capability List support: off
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: serial bus (0x0c)
Subclass Name: SMBus (0x05)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00000000 0x00000000 0x00000000 0x00000000
0x20: 0x00001881 0x00000000 0x00000000 0x052d1014
0x30: 0x00000000 0x00000000 0x00000000 0x0000020b
Base address register at 0x10
not implemented(?)
Base address register at 0x14
not implemented(?)
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
type: 16-bit i/o
base: 0x00001880, size: 0x00000020
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x052d
Expansion ROM Base Address: 0x00000000
Reserved @ 0x34: 0x00000000
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x02 (pin B)
Interrupt line: 0x0b
Device-dependent header:
0x40: 0x00000001 0x00000000 0x00000000 0x00000000
0x50: 0x00000000 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82801DB SMBus Controller (SMBus serial bus, revision 0x01) at pci0 dev 31 function 3 (tag 0x8000fb00, intrtag 0x8000fb00, intrswiz 0, intrpin 0x2, i/o on, mem off, no quirks) not configured
auich0 at pci0 dev 31 function 5: PCI configuration registers:
Common header:
0x00: 0x24c58086 0x02900007 0x04010001 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82801DB AC97 Audio Controller (0x24c5)
Command register: 0x0007
I/O space accesses: on
Memory space accesses: on
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: multimedia (0x04)
Subclass Name: audio (0x01)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00001c01 0x000018c1 0xc0000c00 0xc0000800
0x20: 0x00000000 0x00000000 0x00000000 0x05371014
0x30: 0x00000000 0x00000050 0x00000000 0x0000020b
Base address register at 0x10
type: 16-bit i/o
base: 0x00001c00, size: 0x00000100
Base address register at 0x14
type: 16-bit i/o
base: 0x000018c0, size: 0x00000040
Base address register at 0x18
type: 32-bit nonprefetchable memory
base: 0xc0000c00, size: 0x00000200
Base address register at 0x1c
type: 32-bit nonprefetchable memory
base: 0xc0000800, size: 0x00000100
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x0537
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x50
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x02 (pin B)
Interrupt line: 0x0b
Capability register at 0x50
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00000109 0x00000000 0x00000000 0x00000000
0x50: 0xc9c20001 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82801DB AC97 Audio Controller (audio multimedia, revision 0x01) at ? dev 31 function 5 (tag 0x8000fd00, intrtag 0x8000fd00, intrswiz 0, intrpin 0x2, i/o on, mem on, no quirks): i82801DB/DBM (ICH4/ICH4M) AC-97 Audio
auich0: interrupting at irq 11
auich0: ac97: Analog Devices AD1981B codec; headphone, 20 bit DAC, no 3D stereo
auich0: ac97: ext id 601<AC97_22,AMAP,VRA>
Intel 82801DB AC97 Modem Controller (modem communications, revision 0x01) at pci0 dev 31 function 6: PCI configuration registers:
Common header:
0x00: 0x24c68086 0x02900005 0x07030001 0x00000000
Vendor Name: Intel (0x8086)
Device Name: 82801DB AC97 Modem Controller (0x24c6)
Command register: 0x0005
I/O space accesses: on
Memory space accesses: off
Bus mastering: on
Special cycles: off
MWI transactions: off
Palette snooping: off
Parity error checking: off
Address/data stepping: off
System error (SERR): off
Fast back-to-back transactions: off
Status register: 0x0290
Capability List support: on
66 MHz capable: off
User Definable Features (UDF) support: off
Fast back-to-back capable: on
Data parity error detected: off
DEVSEL timing: medium (0x1)
Slave signaled Target Abort: off
Master received Target Abort: off
Master received Master Abort: off
Asserted System Error (SERR): off
Parity error detected: off
Class Name: communications (0x07)
Subclass Name: modem (0x03)
Interface: 0x00
Revision ID: 0x01
BIST: 0x00
Header Type: 0x00 (0x00)
Latency Timer: 0x00
Cache Line Size: 0x00
Type 0 ("normal" device) header:
0x10: 0x00002401 0x00002001 0x00000000 0x00000000
0x20: 0x00000000 0x00000000 0x00000000 0x05591014
0x30: 0x00000000 0x00000050 0x00000000 0x0000020b
Base address register at 0x10
type: 16-bit i/o
base: 0x00002400, size: 0x00000100
Base address register at 0x14
type: 16-bit i/o
base: 0x00002000, size: 0x00000080
Base address register at 0x18
not implemented(?)
Base address register at 0x1c
not implemented(?)
Base address register at 0x20
not implemented(?)
Base address register at 0x24
not implemented(?)
Cardbus CIS Pointer: 0x00000000
Subsystem vendor ID: 0x1014
Subsystem ID: 0x0559
Expansion ROM Base Address: 0x00000000
Capability list pointer: 0x50
Reserved @ 0x38: 0x00000000
Maximum Latency: 0x00
Minimum Grant: 0x00
Interrupt pin: 0x02 (pin B)
Interrupt line: 0x0b
Capability register at 0x50
type: 0x01 (Power Management, rev. 1.0)
Device-dependent header:
0x40: 0x00000000 0x00000000 0x00000000 0x00000000
0x50: 0xc9c20001 0x00000000 0x00000000 0x00000000
0x60: 0x00000000 0x00000000 0x00000000 0x00000000
0x70: 0x00000000 0x00000000 0x00000000 0x00000000
0x80: 0x00000000 0x00000000 0x00000000 0x00000000
0x90: 0x00000000 0x00000000 0x00000000 0x00000000
0xa0: 0x00000000 0x00000000 0x00000000 0x00000000
0xb0: 0x00000000 0x00000000 0x00000000 0x00000000
0xc0: 0x00000000 0x00000000 0x00000000 0x00000000
0xd0: 0x00000000 0x00000000 0x00000000 0x00000000
0xe0: 0x00000000 0x00000000 0x00000000 0x00000000
0xf0: 0x00000000 0x00000000 0x00000f60 0x00000000
Don't know how to pretty-print device-dependent header.
Intel 82801DB AC97 Modem Controller (modem communications, revision 0x01) at pci0 dev 31 function 6 (tag 0x8000fe00, intrtag 0x8000fe00, intrswiz 0, intrpin 0x2, i/o on, mem off, no quirks) not configured
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
isapnp0: no ISA Plug 'n Play devices found
WARNING: Callback scheduled before sysmon task queue thread present.
auich0: measured ac97 link rate at 48003 Hz, will use 48000 Hz
audio0 at auich0: full duplex, mmap, independent
Kernelized RAIDframe activated
ehci0: handing over full speed device on port 1 to uhci0
uhub3: port 1, device disappeared after reset
uhub4 at uhub0 port 1
uhub4: Texas Instruments TUSB2046 hub, class 9/0, rev 1.10/1.25, addr 2
uhub4: 4 ports with 4 removable, self powered
wd0 at atabus0 drive 0: <TOSHIBA MK6021GAS>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 57231 MB, 116280 cyl, 16 head, 63 sec, 512 bytes/sect x 117210240 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd0(piixide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
atapibus0 at atabus1: 2 targets
cd0 at atapibus0 drive 0: <HL-DT-STCD-RW/DVD DRIVE GCC-4242N, , 0201> cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (Ultra/33) (using DMA)
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
uplcom0 at uhub4 port 2
uplcom0: Prolific Technology PL2303 Serial adapter (ATEN/IOGEAR UC232A), rev 1.10/2.00, addr 3
ucom0 at uplcom0
uhidev0 at uhub4 port 3 configuration 1 interface 0
uhidev0: Logitech N48, rev 1.00/4.01, addr 4, iclass 3/1
ums0 at uhidev0: 3 buttons and Z dir.
wsmouse1 at ums0 mux 0
iwi0: link state changed to UP
wsdisplay0: screen 1 added (80x50, vt100 emulation)
wsdisplay0: screen 2 added (80x50, vt100 emulation)
wsdisplay0: screen 3 added (80x50, vt100 emulation)
wsdisplay0: screen 4 added (80x50, vt100 emulation)
--Boundary-00=_bp29Dp16UKuPQrs
Content-Type: text/plain;
charset="us-ascii";
name="dmesg_pcmcia"
Content-Transfer-Encoding: 7bit
Content-Disposition: inline;
filename="dmesg_pcmcia"
cbb1: 0x00000000 card inserted, 0x30000510
pccbb_pcmcia_socket_enable: 5V card
pccbb_power: CARDBUS_VCC_0V and CARDBUS_VPP_0V [0x44]
pccbb_power: CARDBUS_VCC_5V and CARDBUS_VPP_VCC [0x15]
pccbb_pcmcia_delay: "pccen1" 0x0, sleep 1 ms
pccbb_pcmcia_delay: "pccen2" 0x0, sleep 20 ms
pccbb_pcmcia_delay: "pccwr0" 0x0, sleep 10 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 100 ms
pcmcia1: ++enabled_count = 1
rbus_space_alloc: addr 0, size 1000, mask fff, align 1000
pccbb_pcmcia_alloc_mem: addr 0x40000000 size 0x400, realsize 0x1000
pccbb_pcmcia_mem_map window 0 bus 40000000+0+400 at card addr 0
pccbb_pcmcia_do_mem_map: start 0x40000000 end 0x400003ff off 0xc0000000
pccbb_pcmcia_do_mem_map window 0: 0000 0080 0040 40
pccbb_pcmcia_mem_map window 0 bus 40000000+0+400 at card addr 0
pccbb_pcmcia_do_mem_map: start 0x40000000 end 0x400003ff off 0xc0000000
pccbb_pcmcia_do_mem_map window 0: 0000 0080 0000 40
pcmcia1: CIS version PCMCIA 2.0 or 2.1
pcmcia1: CIS info: Zoom-VENUS, PCMCIA V92 DataFax
pcmcia1: Manufacturer code 0x200, product 0x1
pcmcia1: function 0: serial port, ccr addr ff80 mask 67
pcmcia1: function 0, config table entry 15: I/O card; irq mask 86bc; iomask a, iospace 3f8-3ff; rdybsy_active io8 irqshare irqpulse irqlevel powerdown audio
pcmcia1: function 0, config table entry 23: I/O card; irq mask 86bc; iomask a, iospace 2f8-2ff; rdybsy_active io8 irqshare irqpulse irqlevel powerdown audio
pcmcia1: function 0, config table entry 31: I/O card; irq mask 86bc; iomask a, iospace 3e8-3ef; rdybsy_active io8 irqshare irqpulse irqlevel powerdown audio
pcmcia1: function 0, config table entry 39: I/O card; irq mask 86bc; iomask a, iospace 2e8-2ef; rdybsy_active io8 irqshare irqpulse irqlevel powerdown audio
com3 at pcmcia1 function 0: <Zoom-VENUS, PCMCIA V92 DataFax>
pcmcia_config_alloc: io 0 start=3f8 length=8 align=400 skew=3f8
rbus_space_alloc: addr 3f8, size 8, mask 3ff, align 400
pccbb_pcmcia_io_alloc alloc port 0x4000+0x8
pccbb_pcmcia_io_map window 0 io8 port 4000+8
pccbb_pcmcia_do_io_map win 0 addr 0x4000 size 0x8 width 8
start 00 40, stop 07 40, ioctl 00 enable 40
window iobase 4000 iomax 4007
function iobase 4000 iomax 4007
pccbb_intr_establish start. 0x0
pccbb_intr_establish add pil. 0xc15e7f00
pcmcia1: ++enabled_count = 2
cbb1: pccbb_pcmcia_socket_settype 01 type io 70
rbus_space_alloc: addr 0, size 1000, mask fff, align 1000
pccbb_pcmcia_alloc_mem: addr 0x40000000 size 0x14, realsize 0x1000
pccbb_pcmcia_mem_map window 0 bus 40000000+f80+14 at card addr f000
pccbb_pcmcia_do_mem_map: start 0x40000000 end 0x40000f93 off 0xc000f000
pccbb_pcmcia_do_mem_map window 0: 0000 0080 0f40 40
pcmcia1: function 0 CCR at 0 offset f80: 4f 88 ee 0, 0 40 ff ff, ff
com3: ns16550a, working fifo
pcmcia1: --enabled_count = 1
pccbb_intr_disestablish start. 0xc15e7f00
pccbb_intr_disestablish: pil 0xc15e7f00
pccbb_intr_disestablish frees one pil
pccbb_intr_disestablish frees one pil
pccbb_intr_disestablish: no interrupt handler
pccbb_pcmcia_socket_disable
pccbb_power: CARDBUS_VCC_0V and CARDBUS_VPP_0V [0x44]
pccbb_pcmcia_delay: "pccwr1" 0x0, sleep 300 ms
pcmcia1: --enabled_count = 0
--Boundary-00=_bp29Dp16UKuPQrs--