Hello people!

I have a problem getting my D-Link USB Fast Ethernet DU-E100
adapter to work. The device is detected and I can use ifconfig
to both show information and configure addresses, but i can't
get link. Anybody experienced the same problem ?

According to my 'dmesg' i get this message that is probably
important, but i have the same message after my fxp0 interface
wich works fine:

   OUI 0x0010a9 model 0x0001 rev 0 at aue0 phy 1 not configured




<CUT ifconfig aue0>
aue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        address: 00:50:ba:7c:fe:ed
        media: Ethernet none (none)
        inet 192.168.0.4 netmask 0xffffff00 broadcast 192.168.0.255
        inet6 fe80::250:baff:fe7c:feed%aue0 prefixlen 64 scopeid 0x7
</CUT>

<CUT uname -a>
NetBSD home-ivarhs 1.6_STABLE NetBSD 1.6_STABLE (INETbox)
#0: Fri Nov  8 23:03:56 CET 2002
root@home-ivarhs:/usr/src/sys/arch/i386/compile/INETbox i386
</CUT>

<CUT dmesg (network part) >
fxp0 at pci0 dev 11 function 0: i82559S Ethernet, rev 9
fxp0: interrupting at irq 10
fxp0: Ethernet address 00:d0:c9:37:46:35
OUI 0x005500 model 0x0015 rev 4 at fxp0 phy 1 not configured
ohci0 at pci0 dev 19 function 0: Compaq USB Controller (rev. 0x06)
ohci0: interrupting at irq 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
aue0 at uhub0 port 2
aue0: USBs USB 10/100 Fast Ethernet, rev 1.10/1.01, addr 2
aue0: Ethernet address 00:50:ba:7c:fe:ed
OUI 0x0010a9 model 0x0001 rev 0 at aue0 phy 1 not configured
</CUT>


The entire 'dmesg' is listed below.


Ragards...

Ivar


<CUT dmesg>
NetBSD 1.6_STABLE (INETbox) #0: Fri Nov  8 23:03:56 CET 2002
    root@home-ivarhs:/usr/src/sys/arch/i386/compile/INETbox
cpu0: Cyrix MMX-enhanced MediaGX (GXm) (586-class), 299.24 MHz
cpu0: features 808131<FPU,TSC,MSR,CX8>
cpu0: features 808131<CMOV,MMX>
total memory = 123 MB
avail memory = 111 MB
using 1607 buffers containing 6428 KB of memory
BIOS32 rev. 0 found at 0xfad70
mainbus0 (root)
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: Cyrix Corporation MediaGX Built-in PCI Host Controller (rev. 0x00)
fxp0 at pci0 dev 11 function 0: i82559S Ethernet, rev 9
fxp0: interrupting at irq 10
fxp0: Ethernet address 00:d0:c9:37:46:35
OUI 0x005500 model 0x0015 rev 4 at fxp0 phy 1 not configured
pcib0 at pci0 dev 18 function 0
pcib0: Cyrix Corporation Cx5530 I/O Companion Multi-Function South Bridge 
(rev. 0x30)
Cyrix Corporation Cx5530 I/O Companion (SMI Status and ACPI Timer) 
(miscellaneous bridge) at pci0 dev 18 function 1 not configured
pciide0 at pci0 dev 18 function 2: Cyrix Corporation Cx5530 I/O Companion 
(IDE Controller) (rev. 0x00)
pciide0: hardware does not support DMA
pciide0: primary channel wired to compatibility mode
pciide0: primary channel ignored (other hardware responding at addresses)
pciide0: secondary channel wired to compatibility mode
pciide0: secondary channel ignored (other hardware responding at addresses)
Cyrix Corporation Cx5530 I/O Companion (XpressAUDIO) (audio multimedia) at 
pci0 dev 18 function 3 not configured
vga1 at pci0 dev 18 function 4: Cyrix Corporation Cx5530 I/O Companion 
(Video Controller) (rev. 0x00)
wsdisplay0 at vga1 kbdmux 1: console (80x25, vt100 emulation)
wsmux1: connecting to wsdisplay0
ohci0 at pci0 dev 19 function 0: Compaq USB Controller (rev. 0x06)
ohci0: interrupting at irq 11
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Compaq OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
isa0 at pcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
pckbc0 at isa0 port 0x60-0x64
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
wd0 at wdc0 channel 0 drive 0: <IC25N020ATCS04-0>
wd0: drive supports 16-sector PIO transfers, LBA addressing
wd0: 19077 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 39070080 sectors
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wdc1 at isa0 port 0x170-0x177 irq 15
wd1 at wdc1 channel 0 drive 0: <SanDisk SDCFB-128>
wd1: drive supports 1-sector PIO transfers, LBA addressing
wd1: 122 MB, 980 cyl, 8 head, 32 sec, 512 bytes/sect x 250880 sectors
pcppi0 at isa0 port 0x61
midi0 at pcppi0: PC speaker
spkr0 at pcppi0
sysbeep0 at pcppi0
isapnp0 at isa0 port 0x279: ISA Plug 'n Play device support
fdc0 at isa0 port 0x3f0-0x3f7 irq 6 drq 2
isapnp0: no ISA Plug 'n Play devices found
biomask fbed netmask ffed ttymask ffef
IPsec: Initialized Security Association Processing.
aue0 at uhub0 port 2
aue0: USBs USB 10/100 Fast Ethernet, rev 1.10/1.01, addr 2
aue0: Ethernet address 00:50:ba:7c:fe:ed
OUI 0x0010a9 model 0x0001 rev 0 at aue0 phy 1 not configured
boot device: wd0
root on wd0a dumps on wd0b
root file system type: ffs
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
</CUT>




_________________________________________________________________
MSN 8 with e-mail virus protection service: 2 months FREE* 
http://join.msn.com/?page=features/virus