On Tue, 21 May 2002, Chris Lloyd wrote:

> Okay, cool. Now I know it's not a lack of kernel support or something similar
> I'll look into my problem again.

Have you find a reason for your problem? I ask this because it seems that
we have similar problems. ogle compiled fine on my system, but I'm not
able to play any DVD. As a user I get an error message regarding the
permissions of my DVD drive:
libdvdread: Can't open /dev/rcd0d for reading.

This can be fixed, so that's not a real problem. When I start ogle as toor
I get the following:
libdvdcss debug: GetASF not authenticated (ASF=0)
libdvdcss debug: requesting AGID

and so my whole system freezes for about 90 seconds. After this:
libdvdcss error: ioctl_SendChallenge failed
libdvdcss debug: fatal error in CSS Init
libdvdread: Can't open /dev/rcd0d for reading.
vm: faild to open/read the DVD

In the dmesg output I can see the following at the end after one try to
start ogle as toor:
cd0(pciide0:1:0):  Check Condition on CDB: 0xa3 00 00 00 00 00 00 00 00 10
c1 00
    SENSE KEY:  Hardware Error
     ASC/ASCQ:  ASC 0x08 ASCQ 0x03

My drives:
pciide0 at pci0 dev 7 function 1: VIA Technologies VT82C686A (Apollo
KX133) ATA100 controller
pciide0: bus-master DMA support present
pciide0: primary channel configured to compatibility mode
wd0 at pciide0 channel 0 drive 0: <IC35L040AVER07-0>
wd0: drive supports 16-sector pio transfers, lba addressing
wd0: 39266 MB, 16383 cyl, 16 head, 63 sec, 512 bytes/sect x 80418240
sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5
pciide0: primary channel interrupting at irq 14
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 (using DMA data
transfers)
pciide0: secondary channel configured to compatibility mode
atapibus0 at pciide0 channel 1
cd0 at atapibus0 drive 0: <TOSHIBA DVD-ROM SD-M1502, 3100609038, 1012>
type 5 cdrom removable
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
cd1 at atapibus0 drive 1: <SONY    CD-RW  CRX175A1, , 5YS2> type 5 cdrom
removable
cd1: 32-bit data port
cd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2
pciide0: secondary channel interrupting at irq 15
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 (using DMA data
transfers)
cd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2 (using DMA data
transfers)

My system:
NetBSD trinity.matrix.invalid 1.5.1 NetBSD 1.5.1 (MYKERNEL_SUMMER) #0: Wed
May 22 00:59:45 CEST 2002

toor@trinity.matrix.invalid:/usr/src/sys/arch/i386/compile/MYKERNEL_SUMMER
i386

Any ideas, what I can try?


Ciao , Frank .