Re: Dom0 with enabled ACPI doesn't recognize my IDE drives.

["Marcin M. Jessa" <lists%yazzy.org@localhost>]

On 03/26/2010 11:37 AM, Manuel Bouyer wrote:
> On Fri, Mar 26, 2010 at 11:26:34AM +0100, Marcin M. Jessa wrote:
>    
> > On 03/26/2010 11:22 AM, Manuel Bouyer wrote:
> >      
> > > Can you send the dmesg of this kernel which finds all the drives ?
> > >        
> > Output of dmesg's attached.
> >      
> Sorry, I meant, the GENERIC kernel with ACPI enabled.
> BTW, this kernel sees both CPUs too. What's the problem ?
>
>    

Sort of, I can see this in NetBSD's dmesg:
cpu0 at mainbus0 apid 0: (boot processor)
cpu1 at mainbus0 apid 1: (application processor)

And this in xm dmesg:
(XEN) Processor #0 15:5 APIC version 16
(XEN) Processor #1 15:5 APIC version 16
(XEN) Enabling APIC mode:  Flat.  Using 3 I/O APICs
(XEN) Using scheduler: SMP Credit Scheduler (credit)
(XEN) Detected 2004.559 MHz processor.
(XEN) CPU0: AMD Opteron(tm) Processor 246 stepping 08
(XEN) Booting processor 1/1 eip 90000
(XEN) AMD: Disabling C1 Clock Ramping Node #0
(XEN) AMD: Disabling C1 Clock Ramping Node #1
(XEN) CPU1: AMD Opteron(tm) Processor 246 stepping 08
(XEN) Total of 2 processors activated.
(XEN) ENABLING IO-APIC IRQs
(XEN)  -> Using new ACK method
(XEN) Platform timer overflows in 2 jiffies.
(XEN) Platform timer is 1.193MHz PIT
(XEN) Brought up 2 CPUs

...but why then top shows only one CPU with this kernel and 2 CPUs with 
GENERIC...?
I attached dmesg output of GENERIC kernel with enabled ACPI (both kernel 
and BIOS).

And the main problem still remains, why can't Dom0 boot with BIOS 
enabled ACPI..?



Thanks,
Marcin

Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.0.2_PATCH (GENERIC) #0: Fri Mar 26 02:24:12 CET 2010
        
root%zeus.yazzy.org@localhost:/usr/amd64/obj-amd64/sys/arch/amd64/compile/GENERIC
total memory = 4030 MB
avail memory = 3892 MB
timecounter: Timecounters tick every 10.000 msec
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.34 @ 0xfbf7c000 (33 entries)
RIOWORKS HDAMA ( )
mainbus0 (root)
cpu0 at mainbus0 apid 0: AMD 686-class, 2004MHz, id 0xf58
cpu0: erratum 89 present
cpu0: erratum 97 present
cpu0: erratum 101 present
cpu0: WARNING: errata present, BIOS upgrade may be
cpu0: WARNING: necessary to ensure reliable operation
cpu1 at mainbus0 apid 1: AMD 686-class, 2004MHz, id 0xf58
ioapic0 at mainbus0 apid 2: pa 0xfec00000, version 11, 24 pins
ioapic1 at mainbus0 apid 3: pa 0xfc000000, version 11, 4 pins
ioapic2 at mainbus0 apid 4: pa 0xfc001000, version 11, 4 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <PTLTD ,    XSDT  ,06040000>, AslId < LTP,00000000>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
acpi0: fixed-feature sleep button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpibut0 at acpi0 (PWRB, PNP0C0C): ACPI Power Button
attimer1 at acpi0 (TMR, PNP0100): AT Timer
attimer1: io 0x40-0x43 irq 0
pcppi1 at acpi0 (SPKR, PNP0800)
pcppi1: io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
pckbc1 at acpi0 (KBC, PNP0303): kbd port
pckbc1: io 0x60,0x64 irq 1
UAR1 (PNP0501) at acpi0 not configured
UAR2 (PNP0501) at acpi0 not configured
ECP1 (PNP0401) at acpi0 not configured
attimer1: attached to pcppi1
pckbd0 at pckbc1 (kbd slot)
pckbc1: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard
pci0 at mainbus0 bus 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
ohci0 at pci0 dev 0 function 0: vendor 0x1022 product 0x7464 (rev. 0x0b)
ohci0: interrupting at ioapic0 pin 19
ohci0: OHCI version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
ohci1 at pci0 dev 0 function 1: vendor 0x1022 product 0x7464 (rev. 0x0b)
ohci1: interrupting at ioapic0 pin 19
ohci1: OHCI version 1.0, legacy support
usb1 at ohci1: USB revision 1.0
vga0 at pci0 dev 6 function 0: vendor 0x1002 product 0x4752 (rev. 0x27)
wsdisplay0 at vga0 kbdmux 1: console (80x25, vt100 emulation), using wskbd0
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
pci1 at mainbus0 bus 2
pci1: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
bge0 at pci1 dev 3 function 0: Broadcom BCM5702X Gigabit Ethernet
bge0: interrupting at ioapic1 pin 3
bge0: ASIC BCM5703 A2 (0x1002), Ethernet address 00:50:45:00:b1:d7
brgphy0 at bge0 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
bge1 at pci1 dev 4 function 0: Broadcom BCM5702X Gigabit Ethernet
bge1: interrupting at ioapic1 pin 3
bge1: ASIC BCM5703 A2 (0x1002), Ethernet address 00:50:45:00:b1:d8
brgphy1 at bge1 phy 1: BCM5703 1000BASE-T media interface, rev. 2
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 
1000baseT-FDX, auto
pci2 at mainbus0 bus 3
pci2: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
satalink0 at pci2 dev 2 function 0
satalink0: Silicon Image SATALink 3114 (rev. 0x02)
satalink0: 33MHz PCI bus
satalink0: bus-master DMA support present
satalink0: using ioapic2 pin 2 for native-PCI interrupt
atabus0 at satalink0 channel 0
atabus1 at satalink0 channel 1
atabus2 at satalink0 channel 2
atabus3 at satalink0 channel 3
isa0 at mainbus0
lpt0 at isa0 port 0x378-0x37b irq 7
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com1 at isa0 port 0x2f8-0x2ff irq 3: ns16550a, working fifo
wdc0 at isa0 port 0x1f0-0x1f7 irq 14
atabus4 at wdc0 channel 0
wdc1 at isa0 port 0x170-0x177 irq 15
atabus5 at wdc1 channel 0
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
satalink0: port 1: device present, speed: 1.5Gb/s
satalink0: port 2: device present, speed: 1.5Gb/s
wd0 at atabus1 drive 0: <SAMSUNG HD321KJ>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
uhub0 at usb0: vendor 0x1022 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
uhub1 at usb1: vendor 0x1022 OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd0(satalink0:1:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd1 at atabus2 drive 0: <SAMSUNG HD321KJ>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 298 GB, 620181 cyl, 16 head, 63 sec, 512 bytes/sect x 625142448 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 7
wd1(satalink0:2:0): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
wd2 at atabus4 drive 0: <WDC WD5000AAKB-00H8A0>
wd2: drive supports 16-sector PIO transfers, LBA48 addressing
wd2: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd2: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd3 at atabus4 drive 1: <WDC WD5000AAKB-00H8A0>
wd3: drive supports 16-sector PIO transfers, LBA48 addressing
wd3: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd3: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
umass0 at uhub1 port 1 configuration 1 interface 0
umass0: Western Digital External HDD, rev 2.00/1.07, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
sd0 at scsibus0 target 0 lun 0: <WD, 2500JB External, 0107> disk fixed
sd0: fabricating a geometry
sd0: 232 GB, 238475 cyl, 64 head, 32 sec, 512 bytes/sect x 488397168 sectors
sd0: fabricating a geometry
umass1 at uhub1 port 2 configuration 1 interface 0
umass1: Western Digital External HDD, rev 2.00/1.07, addr 3
umass1: using SCSI over Bulk-Only
scsibus1 at umass1: 2 targets, 1 lun per target
sd1 at scsibus1 target 0 lun 0: <WD, 2500JB External, 0107> disk fixed
sd1: fabricating a geometry
sd1: 232 GB, 238475 cyl, 64 head, 32 sec, 512 bytes/sect x 488397168 sectors
sd1: fabricating a geometry
umass1: at uhub1 port 2 (addr 3) disconnected
sd1: detached
scsibus1: detached
umass1: detached
wd4 at atabus5 drive 0: <ST3500630A>
wd4: quirks 2<FORCE_LBA48>
wd4: drive supports 16-sector PIO transfers, LBA48 addressing
wd4: 465 GB, 969021 cyl, 16 head, 63 sec, 512 bytes/sect x 976773168 sectors
wd4: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio0 at pad0: half duplex
raid2: RAID Level 1
raid2: Components: component0[**FAILED**] /dev/wd1a
raid2: Total Sectors: 625142272 (305245 MB)
raid0: RAID Level 1
raid0: Components: /dev/wd3a /dev/wd2a
raid0: Total Sectors: 976772992 (476939 MB)
boot device: raid0
root on raid0a dumps on raid0b
root file system type: ffs
umass1 at uhub1 port 2 configuration 1 interface 0
umass1: Western Digital External HDD, rev 2.00/1.07, addr 3
umass1: using SCSI over Bulk-Only
scsibus1 at umass1: 2 targets, 1 lun per target
sd1 at scsibus1 target 0 lun 0: <WD, 2500JB External, 0107> disk fixed
sd1: fabricating a geometry
sd1: 232 GB, 238475 cyl, 64 head, 32 sec, 512 bytes/sect x 488397168 sectors
sd1: fabricating a geometry
wsdisplay0: screen 1 added (80x25, vt100 emulation)
wsdisplay0: screen 2 added (80x25, vt100 emulation)
wsdisplay0: screen 3 added (80x25, vt100 emulation)
wsdisplay0: screen 4 added (80x25, vt100 emulation)
raid2: Error re-writing parity!