Re: -current on 7600-type machine

[John Klos <john%ziaspace.com@localhost>]

> I think I found where the problem is.
>
> Could you try the following patch for src/sys/arch/macppc/dev/if_mc.c ?
>
> --- if_mc.c.orig        2008-09-02 01:33:10.000000000 +0200
> +++ if_mc.c     2008-09-02 01:32:54.000000000 +0200

Yep. That fixes the problem, and now I get all the way to "boot device:" 
before it hangs. Not sure if this is a problem with the IDE card, as I 
have no SCSI drives from which to try to boot... One step at a time!



> > NetBSD/macppc OpenFirmware Boot, Revision 1.10
> > (builds@wb36, Thu Oct 18 06:37:27 PDT 2007)
no active package5362152+343768 [254192+237796]=0x5e9688
 start=0x100000
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 4.99.72 (ANDROMEDA-$Revision: 4.713 $) #3: Mon Sep  1 17:08:02 PDT 2008

john%maya.ziaspace.com@localhost:/usr/current/obj/sys/arch/macppc/compile/ANDROMEDA
total memory = 1024 MB
avail memory = 990 MB
found Grand Central PIC at f3000000
bootpath: /bandit@F2000000/ACARD,6260@D/disk@0/netbsd
mainbus is not split
mainbus0 (root)
cpu is not split
cpu0 at mainbus0: 750 (Revision 3.2), ID 0 (primary)
cpu0: HID0 8290c0a4<EMCP,ECLK,DOZE,DPM,ICE,DCE,SGE,BTIC,BHT>, powersave: 1
cpu0: 500.00 MHz, no-parity 1MB WB L2 cache (PB SRAM) at 2:1 ratio
bandit is not split
bandit0 at mainbus0
pci0 at bandit0 bus 0
pchb is not split
pchb0 at pci0 dev 11 function 0
pchb0: Apple Computer Bandit Host-PCI Bridge (rev. 0x03)
acardide0 at pci0 dev 13 function 0
acardide0: Acard ATP860-A Ultra66 IDE Controller (rev. 0x01)
acardide0: using irq 23 for native-PCI interrupt
atabus0 at acardide0 channel 0
atabus1 at acardide0 channel 1
satalink0 at pci0 dev 14 function 0
satalink0: Silicon Image SATALink 3512 (rev. 0x01)
satalink0: using irq 24 for native-PCI interrupt
atabus2 at satalink0 channel 0
atabus3 at satalink0 channel 1
ex0 at pci0 dev 15 function 0: 3Com 3c905-TX 10/100 Ethernet (rev. 0x0)
ex0: interrupting at irq 25
ex0: MAC address 00:60:97:c1:03:cb
nsphy0 at ex0 phy 24: DP83840 10/100 media interface, rev. 1
nsphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
obio is not split
obio0 at pci0 dev 16 function 0: addr 0xf3000000
esp0 at obio0 offset 0x10000 irq 12: NCR53C94, 25MHz, SCSI ID 7
scsibus0 at esp0: 8 targets, 8 luns per target
mc is not split
mc0 at obio0 offset 0x11000: irq 14,2,3: address 00:a0:40:6b:03:e2
zsc0 at obio0: irq 15,16
zstty0 at zsc0 channel 0 (console i/o)
zstty1 at zsc0 channel 1
awacs at obio0 offset 0x14000 not configured
swim3 at obio0 offset 0x15000 not configured
adb is not split
adb0 at obio0 offset 0x16000 irq 18: 0 targets
aed is not split
aed0 at adb0 addr 0: ADB Event device
mesh is not split
mesh0 at obio0 offset 0x18000 irq 13: 50MHz, SCSI ID 7
scsibus1 at mesh0: 8 targets, 8 luns per target
nvram is not split
nvram0 at obio0 offset 0x1d000
bandit is not split
bandit1 at mainbus0
pci1 at bandit1 bus 1
Apple Computer Control (miscellaneous prehistoric) at pci1 dev 11 function 0 
not configured
biomask 80007fe netmask 80007fe ttymask 80007fe
scsibus0: waiting 15 seconds for devices to settle...
scsibus1: waiting 15 seconds for devices to settle...
wd0 at atabus0 drive 0: <ST3400633A>
wd0: quirks 2<FORCE_LBA48>
wd0: 372 GB, 775221 cyl, 16 head, 63 sec, 512 bytes/sect x 781422768 sectors
boot device: <unknown>
root on wd0d dumps on wd0b