Can't install NETBSD 5.99.61 on D-Link DSM-G600

[Charles Brown <obigiankenobi%gmail.com@localhost>]

Hello,
I'm trying to install NetBSD on my D-Link DSM-G600 Rev.B2.

I'm using this mirror:

http://nyftp.netbsd.org/pub/NetBSD-daily/HEAD/201201290010Z/sandpoint/binary/kernel/

When I try to boot the netbsd-INSTALL kernel via tftp, this is the result:

U-Boot 0.2.0 (Mar 16 2006 - 10:12:43)

CPU:   MPC8245 V1.4 at 170.503 MHz:
Board: Sandpoint 8245
DRAM:  32 MB
FLASH: FUJI_DL323BE
In:    serial
Out:   serial
Err:   serial
Hit any key to stop autoboot:  0
## Booting image at fff10000 ...
   Image Name:   altboot
   Image Type:   PowerPC Linux Kernel Image (unknown compression)
   Data Size:    76028 Bytes = 74.2 kB
   Load Address: 01000000
   Entry Point:  01000000
 Verifying Checksum ... OK
OK
## Loading RAMDisk Image at ffc20000 ...
   Image Name:   dummy
   Image Type:   PowerPC Linux RAMDisk Image (unknown compression)
   Data Size:    0 Bytes =  0 kB
   Load Address: 01f00000
   Entry Point:  01f00000
   Verifying Checksum ... OK
   Loading Ramdisk to 01f2f000, end 01f2f000 ... OK

>> NetBSD/sandpoint altboot, revision 1.9 (Sun Jan 29 10:10:10 UTC 2012)
>> D-Link DSM-G600, cpu 198 MHz, bus 99 MHz, 32MB SDRAM
channel 0 present
wd0: <MAXTOR STM3320820A> DMA LBA LBA48 305245 MB
wd0a: ffs       (63)
wd0b: swap      (624878415)
MAC address 00:19:5b:77:45:4f
100Mbps-FDX
Hit any key to enter interactive mode: 2
bootargs> tftp:netbsd-INSTALL

loading "netbsd-INSTALL" 5300312+148304=0x532830
entry=0x90000, ssym=0x5c23a8, esym=0x5c2830
Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010, 2011, 2012
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.99.61 (INSTALL) #0: Sun Jan 29 10:28:17 UTC 2012
        
builds%b8.netbsd.org@localhost:/home/builds/ab/HEAD/sandpoint/201201290010Z-obj/home/builds/ab/HEAD/src/sys/arch/sandpoint/compile/INSTALL
Model: dlink
total memory = 32768 KB
avail memory = 25952 KB
OpenPIC Version 1.2: Supports 1 CPUs and 26 interrupt sources.
sysctl_createv: sysctl_create(mapped_files) returned 12

After the last message, the kernel hangs and I can only restart the unit.

Kernel 5.99.60 works fine, and I can successfully install the release.
The release available on ftp.netbsd.org also does'nt work (same boot
messages, but the kernel stops with: OpenPIC Version 1.2: Supports 1
CPUs and 26 interrupt sources.)

Anyone have faced this issue?

Please, let me know if you need any further information.
Any help is welcome! :)

Best Regards