[src/netbsd-3]: src/sbin/atactl Pull up revision 1.21 (requested by drochner ...

[tron <tron%NetBSD.org@localhost>]

details:   https://anonhg.NetBSD.org/src/rev/d6029959ec71
branches:  netbsd-3
changeset: 575380:d6029959ec71
user:      tron <tron%NetBSD.org@localhost>
date:      Fri Apr 15 22:11:47 2005 +0000

description:
Pull up revision 1.21 (requested by drochner in ticket #156):
Improve formatting.

diffstat:

 sbin/atactl/atactl.8 |  90 +++++++++++++++++----------------------------------
 1 files changed, 30 insertions(+), 60 deletions(-)

diffs (173 lines):

diff -r 62ab73aaeb30 -r d6029959ec71 sbin/atactl/atactl.8
--- a/sbin/atactl/atactl.8      Fri Apr 15 22:10:07 2005 +0000
+++ b/sbin/atactl/atactl.8      Fri Apr 15 22:11:47 2005 +0000
@@ -1,4 +1,4 @@
-.\"    $NetBSD: atactl.8,v 1.19.2.1 2005/04/15 22:09:10 tron Exp $
+.\"    $NetBSD: atactl.8,v 1.19.2.2 2005/04/15 22:11:47 tron Exp $
 .\"
 .\" Copyright (c) 1998 The NetBSD Foundation, Inc.
 .\" All rights reserved.
@@ -58,24 +58,17 @@
 .Sh DEVICE COMMANDS
 The following commands may be used on IDE and ATA devices.
 Note that not all devices support all commands.
-.Pp
-.Cm identify
-.Pp
+.Bl -tag -width setidleXX
+.It Cm identify
 Identify the specified device, displaying the device's vendor, product,
 revision strings, and the device's capabilities.
-.Pp
-.Cm idle
-.Pp
+.It Cm idle
 Place the specified device into Idle mode.
 This mode may consume less power than Active mode.
-.Pp
-.Cm standby
-.Pp
+.It Cm standby
 Place the specified device into Standby mode.
 This mode will consume less power than Idle mode.
-.Pp
-.Cm sleep
-.Pp
+.It Cm sleep
 Place the specified device into Sleep mode.
 This mode will consume less power than Standby mode,
 but requires a device reset to resume operation.
@@ -83,54 +76,38 @@
 .Xr wd 4
 driver performs this reset automatically,
 but this should still be used with caution.
-.Pp
-.Cm setidle
-.Ar idle-timer
-.Pp
+.It Cm setidle Ar idle-timer
 Places the specified device into Idle mode,
 and sets the Idle timer to
 .Ar idle-timer
 seconds.
 A value of 0 will disable the Idle timer.
-.Pp
-.Cm setstandby
-.Ar standby-timer
-.Pp
+.It Cm setstandby Ar standby-timer
 Places the specified device into Standby mode,
 and sets the Standby timer to
 .Ar standby-timer
 seconds.
 A value of 0 will disable the Standby timer.
-.Pp
-.Cm checkpower
-.Pp
+.It Cm checkpower
 Will print out if the device is in Active, Idle, or Standby power
 management mode.
-.Pp
-.Cm smart
-.Ar [enable | disable | status | offline # | error-log | selftest-log]
-.Pp
+.It Cm smart Bq Ar enable | disable | status | offline # | error-log | selftest-log
 Controls SMART feature set of the specified device.
 SMART stands for Self-Monitoring, Analysis, and Reporting Technology.
 It provides an early warning system by comparing subtle operation
 characteristics to those determined in vendor testing
 to precede device failures.
-.Pp
-.Ar enable
-.Pp
+.Bl -tag -width selftestXlogXX
+.It Ar enable
 Enables access to SMART capabilities within the device.
 Prior to being enabled, a SMART capable device neither
 monitors nor saves SMART attribute values.
 The state of SMART, either enabled or disabled, will
 be preserved by the device across power cycles.
-.Pp
-.Ar disable
-.Pp
+.It Ar disable
 Disables access to SMART capabilities within the device.
 Attribute values will be saved, and will no longer be monitored.
-.Pp
-.Ar status
-.Pp
+.It Ar status
 Reports whether SMART is supported by the device, and whether SMART is
 enabled on the device (can only be determined on ATA6 or better devices).
 If SMART is enabled, then a table of attribute information is printed.
@@ -154,7 +131,9 @@
 corresponding attribute value can equal while still retaining a
 positive reliability status.
 .Pp
-If the crit field is "yes" then negative reliability of this attribute
+If the crit field is
+.Dq yes
+then negative reliability of this attribute
 predicts imminent data loss.
 Otherwise it merely indicates that the intended design life period
 of usage or age has been exceeded.
@@ -162,22 +141,14 @@
 device is online.
 The reliability field indicates whether the attribute
 value is within the acceptable threshold.
-.Pp
-.Ar offline #
-.Pp
+.It Ar offline #
 Runs the numbered offline self-test on the drive.
-.Pp
-.Ar error-log
-.Pp
+.It Ar error-log
 Prints the error log.
-.Pp
-.Ar selftest-log
-.Pp
+.It Ar selftest-log
 Prints the self-test log.
-.Pp
-.Cm security
-.Ar [freeze | status]
-.Pp
+.El
+.It Cm security Bq Ar freeze | status
 Controls
 .Dq security
 (password protection) features of modern ATA drives.
@@ -191,23 +162,22 @@
 sense to issue the
 .Dq freeze
 command early in the boot process.
-.Pp
-.Ar freeze
-.Pp
+.Bl -tag -width freezeXX
+.It Ar freeze
 freezes the drive's security status
-.Pp
-.Ar status
-.Pp
+.It Ar status
 displays the drive's security status
+.El
+.El
 .Sh BUS COMMANDS
 The following commands may be used on IDE and ATA busses.
 Note that not all devices support all commands.
-.Pp
-.Cm reset
-.Pp
+.Bl -tag -width resetXX
+.It Cm reset
 Reset the bus.
 This will reset all ATA devices present on the bus.
 Any ATAPI device with pending commands will also be reset.
+.El
 .Sh SEE ALSO
 .Xr ioctl 2 ,
 .Xr wd 4 ,