fxp problems on amd64

[Adam K Kirchhoff <akirchhoff135014%comcast.net@localhost>]

I have a workstation here onto which I have installed NetBSD 5.1/amd64.  
Everything during the installation went fine and upon rebooting the 
first thing I tried to do was acquire an IP address on the intel NIC, 
which was detected as fxp0:

fxp0 at pci5 dev 5 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at ioapic1 pin 2
fxp0: Ethernet address 00:02:b3:10:15:db
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto

Unfortunately, dhclient fails to acquire an IP address.  If I manually 
set one, I'm still unable to ping the router on the network.  Mind you, 
the NIC is fine as slackware, vista, and FreeBSD all work with it.  I 
then downloaded and upgraded from the latest daily ISO.  Once again, the 
NIC failed to acquire an IP address.  The driver can clearly tell if 
there is  cable plugged in, as the status switches from "active" to "no 
carrier".

Now, today I downloaded and burned the i386 5.1 CD and rebooted.  I quit 
out of the installer and ran dhclient from the shell...  And, much to my 
surprise, I was able to get an IP address.

I'm attaching the full dmesg from the 5.1.0_PATCH/amd64.  If there is 
anything I can test to get this working, please let me know.

Adam


Copyright (c) 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004, 2005,
    2006, 2007, 2008, 2009, 2010
    The NetBSD Foundation, Inc.  All rights reserved.
Copyright (c) 1982, 1986, 1989, 1991, 1993
    The Regents of the University of California.  All rights reserved.

NetBSD 5.1.0_PATCH (GENERIC) #0: Sat Mar 26 06:59:39 UTC 2011
        
builds%b7.netbsd.org@localhost:/home/builds/ab/netbsd-5-1/amd64/201103260500Z-obj/home/builds/ab/netbsd-5-1/src/sys/arch/amd64/compile/GENERIC
total memory = 4093 MB
avail memory = 3952 MB
timecounter: Timecounters tick every 10.000 msec
RTC BIOS diagnostic error 11<memory_size>
timecounter: Timecounter "i8254" frequency 1193182 Hz quality 100
SMBIOS rev. 2.3 @ 0xf0450 (102 entries)
Dell Inc.                 Precision WorkStation 490    
mainbus0 (root)
cpu0 at mainbus0 apid 0: Intel 686-class, 3192MHz, id 0xf64
cpu1 at mainbus0 apid 2: Intel 686-class, 3192MHz, id 0xf64
cpu2 at mainbus0 apid 1: Intel 686-class, 3192MHz, id 0xf64
cpu3 at mainbus0 apid 3: Intel 686-class, 3192MHz, id 0xf64
ioapic0 at mainbus0 apid 8: pa 0xfec00000, version 20, 24 pins
ioapic1 at mainbus0 apid 9: pa 0xfec80000, version 20, 24 pins
acpi0 at mainbus0: Intel ACPICA 20080321
acpi0: X/RSDT: OemId <DELL  , B8K    ,00000015>, AslId <ASL ,00000061>
acpi0: SCI interrupting at int 9
acpi0: fixed-feature power button present
timecounter: Timecounter "ACPI-Fast" frequency 3579545 Hz quality 1000
ACPI-Fast 24-bit timer
acpibut0 at acpi0 (VBTN, PNP0C0C): ACPI Power Button
pcppi1 at acpi0 (SPK, PNP0800): io 0x61
midi0 at pcppi1: PC speaker (CPU-intensive output)
sysbeep0 at pcppi1
attimer1 at acpi0 (TMR, PNP0100): io 0x40-0x5f irq 0
COMA (PNP0501) at acpi0 not configured
hpet0 at acpi0 (HPET, PNP0103): mem 0xfed00000-0xfed003ff
timecounter: Timecounter "hpet0" frequency 14318179 Hz quality 2000
attimer1: attached to pcppi1
pci0 at mainbus0 bus 0: configuration mode 1
pci0: i/o space, memory space enabled, rd/line, rd/mult, wr/inv ok
pchb0 at pci0 dev 0 function 0
pchb0: vendor 0x8086 product 0x25c0 (rev. 0x12)
ppb0 at pci0 dev 2 function 0: vendor 0x8086 product 0x25e2 (rev. 0x12)
pci1 at ppb0 bus 1
pci1: i/o space, memory space enabled, rd/line, wr/inv ok
ppb1 at pci1 dev 0 function 0: vendor 0x8086 product 0x3500 (rev. 0x01)
pci2 at ppb1 bus 2
pci2: i/o space, memory space enabled, rd/line, wr/inv ok
ppb2 at pci2 dev 0 function 0: vendor 0x8086 product 0x3510 (rev. 0x01)
pci3 at ppb2 bus 3
pci3: i/o space, memory space enabled, rd/line, wr/inv ok
ppb3 at pci2 dev 1 function 0: vendor 0x8086 product 0x3514 (rev. 0x01)
pci4 at ppb3 bus 4
pci4: i/o space, memory space enabled, rd/line, wr/inv ok
ppb4 at pci1 dev 0 function 3: vendor 0x8086 product 0x350c (rev. 0x01)
ppb4: disabling notification events
pci5 at ppb4 bus 5
pci5: i/o space, memory space enabled, rd/line, wr/inv ok
fxp0 at pci5 dev 5 function 0: i82559 Ethernet, rev 8
fxp0: interrupting at ioapic1 pin 2
fxp0: Ethernet address 00:02:b3:10:15:db
inphy0 at fxp0 phy 1: i82555 10/100 media interface, rev. 4
inphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ppb5 at pci0 dev 3 function 0: vendor 0x8086 product 0x25e3 (rev. 0x12)
pci6 at ppb5 bus 6
pci6: i/o space, memory space enabled, rd/line, wr/inv ok
ppb6 at pci0 dev 4 function 0: vendor 0x8086 product 0x25fa (rev. 0x12)
pci7 at ppb6 bus 7
pci7: i/o space, memory space enabled, rd/line, wr/inv ok
vga0 at pci7 dev 0 function 0: vendor 0x1002 product 0x9442 (rev. 0x00)
wsdisplay0 at vga0 kbdmux 1
wsmux1: connecting to wsdisplay0
drm at vga0 not configured
azalia0 at pci7 dev 0 function 1: Generic High Definition Audio Controller
azalia0: interrupting at ioapic0 pin 17
azalia0: host: 0x1002/0xaa30 (rev. 0), HDA rev. 1.0
ppb7 at pci0 dev 5 function 0: vendor 0x8086 product 0x25e5 (rev. 0x12)
pci8 at ppb7 bus 8
pci8: i/o space, memory space enabled, rd/line, wr/inv ok
ppb8 at pci0 dev 6 function 0: vendor 0x8086 product 0x25e6 (rev. 0x12)
pci9 at ppb8 bus 9
pci9: i/o space, memory space enabled, rd/line, wr/inv ok
ppb9 at pci0 dev 7 function 0: vendor 0x8086 product 0x25e7 (rev. 0x12)
pci10 at ppb9 bus 10
pci10: i/o space, memory space enabled, rd/line, wr/inv ok
pchb1 at pci0 dev 16 function 0
pchb1: vendor 0x8086 product 0x25f0 (rev. 0x12)
pchb2 at pci0 dev 16 function 1
pchb2: vendor 0x8086 product 0x25f0 (rev. 0x12)
pchb3 at pci0 dev 16 function 2
pchb3: vendor 0x8086 product 0x25f0 (rev. 0x12)
pchb4 at pci0 dev 17 function 0
pchb4: vendor 0x8086 product 0x25f1 (rev. 0x12)
pchb5 at pci0 dev 19 function 0
pchb5: vendor 0x8086 product 0x25f3 (rev. 0x12)
pchb6 at pci0 dev 21 function 0
pchb6: vendor 0x8086 product 0x25f5 (rev. 0x12)
pchb7 at pci0 dev 22 function 0
pchb7: vendor 0x8086 product 0x25f6 (rev. 0x12)
azalia1 at pci0 dev 27 function 0: Generic High Definition Audio Controller
azalia1: interrupting at ioapic0 pin 16
azalia1: host: 0x8086/0x269a (rev. 9), HDA rev. 1.0
ppb10 at pci0 dev 28 function 0: vendor 0x8086 product 0x2690 (rev. 0x09)
pci11 at ppb10 bus 11
pci11: i/o space, memory space enabled, rd/line, wr/inv ok
uhci0 at pci0 dev 29 function 0: vendor 0x8086 product 0x2688 (rev. 0x09)
uhci0: interrupting at ioapic0 pin 21
usb0 at uhci0: USB revision 1.0
uhci1 at pci0 dev 29 function 1: vendor 0x8086 product 0x2689 (rev. 0x09)
uhci1: interrupting at ioapic0 pin 22
usb1 at uhci1: USB revision 1.0
uhci2 at pci0 dev 29 function 2: vendor 0x8086 product 0x268a (rev. 0x09)
uhci2: interrupting at ioapic0 pin 18
usb2 at uhci2: USB revision 1.0
uhci3 at pci0 dev 29 function 3: vendor 0x8086 product 0x268b (rev. 0x09)
uhci3: interrupting at ioapic0 pin 23
usb3 at uhci3: USB revision 1.0
ehci0 at pci0 dev 29 function 7: vendor 0x8086 product 0x268c (rev. 0x09)
ehci0: interrupting at ioapic0 pin 21
ehci0: BIOS has given up ownership
ehci0: EHCI version 1.0
ehci0: companion controllers, 2 ports each: uhci0 uhci1 uhci2 uhci3
usb4 at ehci0: USB revision 2.0
ppb11 at pci0 dev 30 function 0: vendor 0x8086 product 0x244e (rev. 0xd9)
pci12 at ppb11 bus 12
pci12: i/o space, memory space enabled
ichlpcib0 at pci0 dev 31 function 0
ichlpcib0: vendor 0x8086 product 0x2670 (rev. 0x09)
timecounter: Timecounter "ichlpcib0" frequency 3579545 Hz quality 1000
ichlpcib0: 24-bit timer
ichlpcib0: TCO timer reboot disabled by hardware; hope SMBIOS properly handles 
it.
ichlpcib0: TCO (watchdog) timer configured.
piixide0 at pci0 dev 31 function 1
piixide0: Intel 631xESB/632xESB IDE Controller (rev. 0x09)
piixide0: bus-master DMA support present
piixide0: primary channel configured to compatibility mode
piixide0: primary channel interrupting at ioapic0 pin 14
atabus0 at piixide0 channel 0
piixide0: secondary channel configured to compatibility mode
piixide0: secondary channel ignored (disabled)
piixide1 at pci0 dev 31 function 2
piixide1: Intel 631xESB/632xESB Serial ATA Controller (rev. 0x09)
piixide1: bus-master DMA support present
piixide1: primary channel configured to native-PCI mode
piixide1: using ioapic0 pin 20 for native-PCI interrupt
atabus1 at piixide1 channel 0
piixide1: secondary channel configured to native-PCI mode
atabus2 at piixide1 channel 1
ichsmb0 at pci0 dev 31 function 3: vendor 0x8086 product 0x269b (rev. 0x09)
ichsmb0: interrupting at ioapic0 pin 17
iic0 at ichsmb0: I2C bus
isa0 at ichlpcib0
com0 at isa0 port 0x3f8-0x3ff irq 4: ns16550a, working fifo
com0: console
pckbc0 at isa0 port 0x60-0x64
timecounter: Timecounter "clockinterrupt" frequency 100 Hz quality 0
timecounter: Timecounter "TSC" frequency 3192050520 Hz quality 3000
azalia0: codec[0]: ATI R600 HDMI (rev. 1.0), HDA rev. 1.0
audio0 at azalia0: full duplex, playback, capture, independent
azalia1: codec[0]: Sigmatel STAC9200 (rev. 34.1), HDA rev. 1.0
audio1 at azalia1: full duplex, playback, capture, independent
atapibus0 at atabus0: 2 targets
uhub0 at usb3: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhub1 at usb2: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
cd0 at atapibus0 drive 1: <TSSTcorp CD-ROM TS-H192C, , DE00> cdrom removable
uhub2 at usb1: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhub3 at usb4: vendor 0x8086 EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub3: 8 ports with 8 removable, self powered
uhub4 at usb0: vendor 0x8086 UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub4: 2 ports with 2 removable, self powered
cd0: 32-bit data port
cd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 2 (Ultra/33)
cd0(piixide0:0:1): using PIO mode 4, DMA mode 2 (using DMA)
wd0 at atabus1 drive 1: <ST3160812AS>
wd0: drive supports 16-sector PIO transfers, LBA48 addressing
wd0: 149 GB, 310019 cyl, 16 head, 63 sec, 512 bytes/sect x 312500000 sectors
wd0: 32-bit data port
wd0: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 6 (Ultra/133)
wd0(piixide1:0:1): using PIO mode 4, Ultra-DMA mode 6 (Ultra/133) (using DMA)
umass0 at uhub3 port 2 configuration 1 interface 0
umass0: LaCie d2 Quadra, rev 2.00/0.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, 1 lun per target
uhidev0 at uhub3 port 2 configuration 1 interface 1sd0 at scsibus0 target 0 lun 
0: <SAMSUNG, HD501LJ, CR10> disk fixed

uhidev0: LaCie d2 Quadra, rev 2.00/0.00, addr 2, iclass 3/0
uhid0 at uhidev0: input=1, output=1, feature=0
sd0: fabricating a geometry
sd0: 465 GB, 476940 cyl, 64 head, 32 sec, 512 bytes/sect x 976773168 sectors
sd0: fabricating a geometry
wd1 at atabus2 drive 0: <WDC WD2500JD-50FYB0>
wd1: drive supports 16-sector PIO transfers, LBA48 addressing
wd1: 232 GB, 484521 cyl, 16 head, 63 sec, 512 bytes/sect x 488397168 sectors
wd1: 32-bit data port
wd1: drive supports PIO mode 4, DMA mode 2, Ultra-DMA mode 5 (Ultra/100)
wd1(piixide1:1:0): using PIO mode 4, Ultra-DMA mode 5 (Ultra/100) (using DMA)
Kernelized RAIDframe activated
pad0: outputs: 44100Hz, 16-bit, stereo
audio2 at pad0: half duplex, playback, capture
uhidev1 at uhub2 port 2 configuration 1 interface 0
uhidev1: Logitech USB Receiver, rev 1.10/19.04, addr 2, iclass 3/1
ukbd0 at uhidev1
boot device: wd1
root on wd1a dumps on wd1b
uhidev2 at uhub1 port 1 configuration 1 interface 0
uhidev2: Logitech USB Receiver, rev 1.10/17.11, addr 2, iclass 3/1
ukbd1 at uhidev2
root file system type: ffs
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev3 at uhub2 port 2 configuration 1 interface 1
uhidev3: Logitech USB Receiver, rev 1.10/19.04, addr 2, iclass 3/1
uhidev3: 4 report ids
ums0 at uhidev3 reportid 1: 16 buttons and Z dir
wsmouse0 at ums0 mux 0
uhid1 at uhidev3 reportid 2: input=2, output=0, feature=0
uhid2 at uhidev3 reportid 3: input=1, output=0, feature=0
uhid3 at uhidev3 reportid 4: input=3, output=0, feature=0
wskbd1 at ukbd1 mux 1
wskbd1: connecting to wsdisplay0
uhidev4 at uhub1 port 1 configuration 1 interface 1
uhidev4: Logitech USB Receiver, rev 1.10/17.11, addr 2, iclass 3/1
uhidev4: 4 report ids
ums1 at uhidev4 reportid 1: 16 buttons and Z dir
wsmouse1 at ums1 mux 0
uhid4 at uhidev4 reportid 2: input=2, output=0, feature=0
uhid5 at uhidev4 reportid 3: input=1, output=0, feature=0
uhid6 at uhidev4 reportid 4: input=3, output=0, feature=0