Re: 8.0 rc1 barfs during install

[Kathe <kathe%sdf.org@localhost>]

umnn, i don't have the equipment to get the video of the screen.
i can provide reports using other operating systems, do let me
know.

> From bounces-netbsd-users-owner-kathe=sdf.org%NetBSD.org@localhost Mon May  7 16:08:41 2018
> From: Hisashi T Fujinaka <htodd%twofifty.com@localhost>
> X-X-Sender: htodd%chris.i8u.org@localhost
> To: Kathe <kathe%sdf.org@localhost>
> cc: martin%duskware.de@localhost, netbsd-users%netbsd.org@localhost
> Subject: Re: 8.0 rc1 barfs during install
> Sender: netbsd-users-owner%NetBSD.org@localhost
>
> My guess is that you're going to have to get a video of the screen
> during installation.
>
> On Mon, 7 May 2018, Kathe wrote:
>
> >> From bounces-netbsd-users-owner-kathe=sdf.org%NetBSD.org@localhost Mon May  7 15:50:58 2018
> >> From: Martin Husemann <martin%duskware.de@localhost>
> >> To: Kathe <kathe%sdf.org@localhost>
> >> Cc: netbsd-users%netbsd.org@localhost
> >> Subject: Re: 8.0 rc1 barfs during install
> >> Sender: netbsd-users-owner%NetBSD.org@localhost
> >>
> >> On Mon, May 07, 2018 at 03:46:33PM +0000, Kathe wrote:
> >>> i have an amd64 system which runs well with freebsd, openbsd and ubuntu.
> >>> with netbsd 8.0 rc1, it barfs while outputing the message below;
> >>> sdhc0: adma error, status ff
> >>> sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff)
> >>> sdhc0: command or data phase inhibited
> >>> sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff)
> >>> sdhc0: command or data phase inhibited
> >>
> >> Could you provide any details?
> >> Does it hang at that point, just wait for a bit and then continue to boot?
> >> If possible send the full output of the dmesg command, please.
> >>
> >> Martin
> >>
> >
> > my system works well with freebsd, openbsd, ubuntu.
> > under netbsd 8.0 rc1, the following message keeps getting printed;
> > sdhc0: adma error, status ff
> > sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff)
> > sdhc0: command or data phase inhibited
> > sdhc0: timeout waiting for mask 0x1 value 0 (state=0xffffffff)
> > sdhc0: command or data phase inhibited
> > sdhc0: timeout waiting for mask 0x1 value 0 (state=0xffffffff)
> > sdhc0: command or data phase inhibited
> > sdhc0: timeout waiting for mask 0x3 value 0 (state=0xffffffff)
> > sdhc0: command or data phase inhibited
> > sdmmc0: sdmmc_mem_enable failed with error 60
> > sdmmc0: couldn't enable card: 60
> >
> > i can't get to the point of plucking out the dmesg, the message
> > above keeps getting repeated till the point i power-down the
> > system.
> >
>
> -- 
> Hisashi T Fujinaka - htodd%twofifty.com@localhost
> BSEE + BSChem + BAEnglish + MSCS + $2.50 = coffee
>